http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
지역 분할 방법에 의한 ISCST3 모델링으로 수도권 지역에서 SO<sub>2</sub> 농도 예측 연구
구윤서,김성태,신봉섭,신동윤,이정주,Koo, Youn-Seo,Kim, Sung-Tae,Shin, Bong-Sup,Shin, Dong-Yoon,Lee, Jeong-Joo 한국환경영향평가학회 2003 환경영향평가 Vol.12 No.4
$SO_2$ concentrations in the Seoul Metropolitan Area (SMA) were predicted by the regional segment ISCST3 modeling. The SMA was segmented by three modeling regions where the weather monitoring station exists since the area of the SMA, approximately $100km{\times}100km$, is too wide to be modeled by one modeling domain. The predicted concentrations by the model were compared with the measured concentrations at 39 air monitoring stations located in the SMA to validate the ISCST3 modeling coupled with the regional segment approach. The predicted concentrations by the regional segment method showed better performance in depicting the measurements than those by the non-segment ISCST3 modeling. The correction methods of the calculated concentrations reviewed were here the correlation method by the first order linear equation and the ratio method of observed to calculated concentrations. The corrected concentrations by two methods showed good agreement with the measured data. The ratio method was, however, easily applicable to the concentration correction in case of a wide modeling region considered in this study.
자동차 선오염원 확산 모델 CAL3QHCR 소개 및 국내 적용에 관한 연구
구윤서,정필수,김아름,이임학 안양대학교 산업기술연구소 2001 自然科學硏究 Vol.8 No.-
현재 우리나라의 환경영향평가에서 약 40%이상이 도로건설환경영향평가를 차지하고 있다. 도로환경영향평가에서 자동차로부터 배출되는 오염물질이 도로주변에 미치는 영향을 예측하기 위해 국내에서는 주로 CALINE3를 이용한다. 그러나 CALINE3는 기상 data의 입력이 특정조건의 1시간 기상자료만 입력되는 단점이 있다. 그래서 본 연구에서는 CALINE3의 단점을 보완해 기상 data를 1시간 간격의 1년 data로서 입력할 수 있으며 교차로의 해석이 가능한 CAL3QHCR모델로 소개하고 국내에서의 적용가능성에 대해 평가하였다. 도로환경영향평가에서 많이 사용하는 CALINE3를 이용하여 계산한 CO농도와 실제 1년 기상자료를 입력하여 CAL3QHCR로 계산한 CO농도를 비교 분석 한 결과 CAL3QHCR의 농도가 높게 나타나는 경향을 볼 수 있었다. 그 이유는 실제 기상현상은 CALINE3를 이용한 영향평가에서 쓰이는 악조건의 기상자료 보다 낮은 풍속 및 안정한 대기 상태가 발생하기 때문이다. 또한 CAL3QHCR을 이용하여 교차로를 해석한 결과, 도로 중심부에서 교차로를 고려하였을 경우가 최고 농도 8.2ppm으로 교차로를 고려하지 않고 모델링한 결과보다 3배정도 높게 나타났다.
역모델링기법을 이용한 매립지 메탄배출량 산정 방법론 검토
구윤서,권희용,손은성,진현진,정병원,허귀석 한국냄새환경학회 2013 실내환경 및 냄새 학회지 Vol.12 No.3
With glowing concern over the effects of global warming, the need to quantify fugitive methane emissions from landfills has increased. The most prevailing method in Korea is to use a methane generation method of FOD (First Order Decay) or to measure the methane flux at the surface directly. They cannot be considered as accurate methods since the uncertainty of input parameters of FOD and variability of landfill surface. As an alternative method, the direct plume measurement method using dispersion model, namely inverse modeling technique, was proposed in this study. In order to validate the inverse modeling procedure with CALMET and CALPUFF, the dispersion modeling was performed with known arbitrary emission rates and then the model concentrations at the particular receptor points were calculated. The inverse modeling was carried out to find the emission rates with the calculated concentrations at the receptor points. The estimated emission rates by inversing process were identical to the given emission rates. It demonstrated that the inverse modeling procedure is accurately defined in this study. The experiment for inverse modeling was carried out to estimate methane emission rates in Daejeon landfill on 06th October. Meteorological variables and methane concentrations at the Daejeon landfill site were measured to organize input data for the inverse modeling during the experiment. The range of estimated emission rates were from 29.65 to 36.68 g/㎡-day by applying the proposed inverse modeling with measured meteorological and concentration values. The major emission areas in the landfill were also identified. In spite of the limited experiment, the inverse modeling technique is proved to be simple and cost saving method to estimate the methane emission rate in the heterogenous landfill surface. The proposed inverse modeling in this study should be further validated by comparisons with methane flux measurement or a tracer experiment. 고형페기물 매립지에서 온실가스 배출량 산정은 기후변화에 대응 측면에서 매우 중요한 사항이다. 국내에서 메탄가스 배출량 산정은 주로 IPCC(Intergovernmental Panel on Climate Change)가이드라인에 근거하여 매립지 표면에서 직접적으로 flux chamber를 이용하여 배출량을 측정하거나, 또는 FOD(First Order Decay)방법에 의존하여 왔다. 그러나 FOD방법은 매립특성을 반영한 매립가스발생속도상수(k)를 정확히 산정하는데 어려움이 존재하고, 또한 표면 발산량을 측정하는 방법은 매립지 표면에서 배출량이 다양하고 측정이 한정된 기간에만 국한된다는 문제점을 내재하고 있다. 대안으로 본 연구에서는 plume measurement의 한 방법으로 대기확산모델을 활용한 역모델링기법을 적용하는 것을 검토하였다. 역모델링에 의해서 매립지 메탄가스 배출량을 직접 계산하기 위한 방법론을 정리하고, 실제 대전매립지에서 측정한 메탄농도를 이용하여 역모델링기법을 적용한 매립지 메탄 배출량 산정하는 방법에 대하여 제시하였다. 역모델링 과정을 검증하기 위해서 임의의 배출량으로 모델링을 수행하여 모델 예측농도와 확산변수 를 계산하였으며, 역으로 예측농도와 확산변수 를 이용하여 배출량을 재산정 하였다. 재산정한 배출량이 임의의 배출량과 동일함을 확인함으로써 본 연구에서 제시하고 있는 역모델링 절차가 적절함을 검증하였다. 또한, 본 연구에서는 역모델링 기법을 적용하여 실제 대전매립지를 대상으로 메탄 배출량 산정하였다. 대전매립지를 대상으로 메탄배출량을 산정한 결과 29.65~36.68 g/㎡-day로 산정되었으며, 주요 메탄 배출지점은 매립지 내의 유사한 지점에서 일관되게 나타났다. 본 연구방법은 기존의 방법과 비교하면, 메탄농도의 측정방법이 간단하고 비용이 적게 소요되므로 지속적인 모니터링이 가능한 장점이 있으며, 불균일한 매립지 표면의 배출량을 비교적 간편하게 산출이 가능한 것으로 파악되었다. 한편, 본 연구는 제한된 실험에 의한 결과이므로 향후 실제 매립지 배출량을 직접 측정하거나, 또는 추적자 실험을 통해서 그 방법론을 추가로 검증할 필요가 있는 것으로 판단된다.