치과 임플란트용 골융합 측정기의 설계 및 평가

이주희,김창일,백종후,조정호,전명표,정영훈,이영진,이정배,이승대,Lee, Joo-Hee,Kim, Chang-Il,Paik, Jong-Hoo,Cho, Jeong-Ho,Chun, Myoung-Pyo,Jeong, Young-Hun,Lee, Young-Jin,Lee, Jeong-Bae,Lee, Seung-Dae 한국전기전자재료학회 2011 전기전자재료학회논문지 Vol.24 No.3

The osseointegration of dental implant is influenced by many factors such as surface geometry, loading and the amount of bone. Thus, stability of the dental implant should be checked periodically. In order to test the stability of dental implant by using resonance frequency analysis, we designed a structure of transducers and fabricated a piezoelectric devices. Using finite element analysis, the thickness and length of piezoelectric device and transducers were tailorized and the optimized frequency of 10 kHz was obtained. The resonance frequency from simulation analysis and evaluation was estimated to be similar as 10 kHz. The osseointegration was further enhanced with increasing frequency from the evaluation result of the finite element analysis.

치과용 초음파 골수술기 설계 및 평가

이주희,오정민,홍연우,김세기,백종후,이영진,이정배,이승대,Lee, Joo-Hee,Oh, Jung-Min,Hong, Younwoo,Kim, Seiki,Paik, Jonghoo,Lee, Young-Jin,Lee, Jeong-Bae,Lee, Seung-Dae 한국전기전자재료학회 2012 전기전자재료학회논문지 Vol.25 No.12

A piezoelectric ultrasonic bone surgical instrument, usually used to remove the tartar out of teeth or to cut the dentine of the tooth, is a recently popular instrument for dental treatment due to its several merits such as small size, low-electric power and precision control of surgical operation. It has typically two parts of a tip and vibration system which is also composed of head, piezoelectric elements and tail-mass. In order to improve the performance of the instrument, it is important to standardize the size of the vibration system without tip for high performance. In this study, a Finite Element Analysis (FEA) was utilized to optimize the structure of ultrasonic instrument in vibration system. Consequently, this study revealed that influence of several tips on property were minimized and it showed good property at the frequency range of 22~32 kHz.

97 동계유니버시아드대회 개최에 따른 덕유산국립공원지역의 경제효과분석에 관한 연구

이주희,한상열 ( Ju Hee Lee,Sang Yeol Han ) 한국산림경제학회 1997 산림경제연구 Vol.5 No.2

의치용 인공치아와 의치상용 레진간의 결합강도에 관한 실험적 연구

이주희,김창회,김영수,Lee, Joo-Hee,Kim, Chang-Whe,Kim, Yung-Soo 대한치과보철학회 1996 대한치과보철학회지 Vol.34 No.3

A principal advantage of a plastic tooth over a porcelain tooth should be its ability to bond to the denture base material. But plastic teeth could craze and wear easily, so more abrasion resistant plastic denture teeth have been developed. To resist abrasion, the degree of cross-linking was increased, but bonding to denture base meterial became more difficult. The purpose of this study was to evaluate the bond strength of plastic teeth and abrasion resistant teeth bonded to heat-curing, self-curing and light-curing denture base material. Denture tooth molds were chosen that had a>8mm diameter. The denture teeth was bonded to three denture base materials and then machined to the same dimensions. Three denture base materials were used as control groups. Prior to tensile testing, the specimens were thermocycled between $5^{\circ}C\;and\;55^{\circ}C$ for 1000cycles. Tensile testing was performed on an Instron Universal testing mechine. Experimental group ; plastic teeth(Justi Imperial)+heat-curing resin(Lucitone 199) plastic teeth(Justi Imperial)+light-curing resin(Triad) plastic teeth(Justi Imperial)+self-curing resin(Vertex SC) abrasion resistant teeth(IPN)+heat-curing resin(Lucitone 199) abrasion resistant teeth(IPN)+light-curing resin(Triad) abrasion resistant teeth(IPN)+self-curing resin(Vertex SC) Control group ; heat-curing resin(Lucitone 199) light-curing resin (Triad) self-curing resin(Vertex SC). The results were as follows : 1. The denture teeth bonded to heat-curing resin showed the cohesive failure and those bonded to the other resins showed adhesive failure. 2. Tensile bond strength of the plastic teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 3. Tensile bond strength of the abrasion resistant teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 4. Tensile bond strength of the plastic teeth to self-curing resin was not significantly different from that of the abrasion-resistant teeth(p>0.05). 5. Tensile bond strength of the plastic teeth to light-curing resin was significantly greater than that of the abrasion resistant teeth(p<0.01).

라즈베리파이 B+를 이용한 사물인터넷기반 주차공간 관리 시스템 구현

이주희,이상훈,이지영,문봉교,Lee Soon Shin,Kim Yoo Shin 한국통신학회 2015 한국통신학회 학술대회논문집 Vol.2015 No.11

Flow and smoke behavior of a longitudinal ventilation tunnel with various velocities using computational fluid dynamics

이주희,권영진,김동은,Lee, J.H.,Kwon, Y.J.,Kim, D.E. Korean Tunnelling and Underground Space Associatio 2014 한국터널지하공간학회논문집 Vol.16 No.1

터널내의 연기거동 및 대피안전성을 평가하기 위하여 수치해석을 수행하였다. 본 연구의 목적은 최근 더욱 길어지고 있는 장대터널의 화재로 인한 연기 및 온도 분포와 안전성을 평가할 수 있는 수치적 방법을 구현하는데 있다. 계산에 사용되는 컴퓨터자원을 최소화하기 위하여 모델로 선정한 터널의 전체길이인 3 km을 사용하는 대신 여러 개의 대피터널이 포함되는 1.5 km만을 해석영역으로 사용하였다. 터널내의 연기거동에 의한 대피자의 안전성을 평가하기 위하여 연기의 밀도에 의한 기시도와 바닥으로부터의 높이를 고려한 SE (smoke environment)값을 사용하였다. 공기 중에 포함된 연기의 밀도는 3차원 전산유체역학을 통하여 구하였다. 이러한 연기 거동에 영향을 미치는 온도분포를 정확하게 모사하기 위하여 터널 벽면을 단열 혹은 일정한 열유속(heat flux) 가정을 사용하는 대신 1차원 열전도(heat conduction)방정식을 이용하여 터널벽면의 온도를 계산하였다. 대피터널간의 거리가 가까울수록 대피자의 안전성은 높아지겠지만 상대적으로 건설비용이 증가하게 된다. 본 연구에서 대피터널의 길이는 250 m로 하였으며 화재 시 제연팬의 운전 조건을 3가지 (팬이 가동되지 않는 조건, 임계풍속이하조건, 임계풍속이상조건)로 나누어 연기의 거동과 온도분포를 고찰하였다. 그리고 화재가 발생한 시간부터 플래쉬오버가 발생한 시간까지의 연기의 거동과 대피자의 상황을 SE를 이용하여 고찰하였다. A numerical analysis on the smoke behavior and evacuee safety has been performed with computational fluid dynamics. The purpose of this study is to build computational processes for an evacuation and prevention of a fire disaster of a 3 km-length tunnel in Korea. To save computational cost, 1.5 km of the tunnel that can include a few cross-passing tunnels is considered. We are going to assess the fire safety in a road tunnel according to the smoke level, which consists of the smoke density and the height from the floor. The smoke density is obtained in detail from three-dimensional unsteady CFD analysis. To obtain proper temperature distributions on the tunnel wall, one-dimensional conduction equation is considered instead of an adiabatic wall boundary or a constant heat flux. The tunnel considered in this study equips the cross passing tunnels for evacuees every 250 m. The distance is critical in both safety and economy. The more cross passing tunnels, the more safe but the more expensive. Three different jet fan operations can be considered in this study; under- and over-critical velocities for normal traffic condition and 0-velocoty operation for the traffic congestion. The SE (smoke environment) level maps show a smoke environment and an evacuating behavior every moment.

표면 처리법에 따른 치과용 합금과 열중합형 레진 간의 결합 강도에 관한 연구

이주희,정은민,장복숙,정동준,허성주,한동후,심준성,Lee Joo-Hee,Jung Eun-Min,Jang Bok-Sook,Chung Dong-June,Heo Seong-Joo,Han Dong-Hoo,Shim June-Sung 대한치과보철학회 2002 대한치과보철학회지 Vol.40 No.4

The purpose of this study is to compare tensile bond strength between Cr-Co alloy and three denture base resins after surface treatment. Following the manufacturer's instructions, 180 bonded specimens were made from three denture base resins (Lucitone 199. Paladent 20. POSS resin) and three surface treatment methods (sandblasting. metal primer. silicoating) 20 samples were made in each group and a half was ther-mocycled 1000 times between $5^{\circ}C$ and $55^{\circ}C$. The tensile bond strength was measured using an Instron with 5mm/min crosshead speed. Data was analyzed with one-way ANOVA, T-test and Duncan test. The results were as follows : 1. Samples with metal primer coating had significantly high tensile bond strength than the other surface treated groups (p<.05). Significantly low tensile bond strength was shown in sand blasted groups (p<.05). 2. No significant difference was observed in metal primer coating groups before and after ther-mocycling (p>.05) 3. Tensile bond strength was decreased in silicoated samples after thermocycling (p<.05). 4. Of the surface treated groups with metal primer, Lucitone 199 had the greatest bond strength and POSS resin and Paladent 20 were followed (p<.05). 5. Of the surface treated groups with silicoating, POSS resin and Lucitone 199 had greater bond strength than Paladent 20 (p<.05).

kMIT를 이용한 비유창성 실어증 환자 음성 언어의 치료효과 연구

이주희,고명환,김현기,홍기환,Lee Ju Hee,Ko Myun Hwan,Kim Hyun Gi,Hong Ki Hwan 대한후두음성언어의학회 2005 대한후두음성언어의학회지 Vol.16 No.2

Melody intonation therepy (MIT) is to improve the linguistic aspects of the verbal utterance for aphasic patients utilizing the intact right brain. It is applied to the aphasic patients with good comprehension, poor fluency, and little available speech are thought to be ideal candidates. The purpose of the study was to investigate the effects of Korean Melody intonation therapy (kMIT) in patients with non-fluent aphasia. Five male non-fluent aphasic patients were participated in this study. Average ages were 49.9 years old. Each therapy took 45-50minutes once a week for six months. Aphasic Screen lest (RISS) was used to assess language parameter such as Auditory comprehension, oral expression, reading, writing and calculation ability before and after kMIT. Mean of Length Utterance, verbal intelligibility and articulation disorder were assessed also. Computerized Speech Lab was used to assess the acoustic characteristics of aphasic patients before and after kMIT. The results are as follows : 1) Auditory comprehension, oral expression, reading, writing and calculation ability of the subjects increased after UH'. However, only oral expression showed significant difference (p<0.05). 2) Mean of Length Utterance of five patients generally increased after Un. 3) After kMIT, verbal intelligibility increased and showed significant difference (p<0.05). 4) Misarticulation rate generally decreased after m. 5) Voice Onset Time of the alveolar lenis /t/ and velar lenis /k/ gradually decreased after kMIT. 6) However, intonation pattern were increased gradually in yes'no question after kMIT.

임플랜트 상부 보철물의 고정 방식에 따른 힘의 분포에 관한 연구 : 나사 유지형 대 시멘트 유지형

이주희,김창회,김영수,Lee Joo-Hee,Kim Chang-Whe,Kim Yung-Soo 대한치과보철학회 2001 대한치과보철학회지 Vol.39 No.2

To compare the stress distribution patterns between cement-retained and screw-retained implant supported fixed prostheses according to four different abutment types, a three dimensional finite element analysis was performed. The hypothetical three unit fixed partial denture case was modelled on the three implants(10mm length and 3.75 diameter) in mandibular bone. Four angles of implantation(vertical, 10, 15 and 20 degree inclined mesially) were created and three different directions of force (vertical, oblique, horizontal) were applied at the center of the second premolar and distal end of the first molar for each cases. Within the limits of this study, the results were as follows, 1. In vertically installed cases, the more stress was concentrated at upper components, but mesially inclined cases, the more stress was concentrated at cortical bone. 2, The more inclined mesially the more stress was observed, especially at cortical bone. 3. The cement-retained models showed lower principal stress and more even stress distribution than the screw-retained models. 4. The similar stress distribution pattern was showed in model 1 and model 2, model 3 and model 4. 5. The more stress was observed when the loads were applied at the distal end of 1st molar than the center of 2nd premolar. 6 The fixture and the model as a whole, lesser stress values were observed when vertical loads were applied as compared to horizontal and oblique loads.

NASA 워크숍 및 해외 착륙임무에 기반한 달 착륙 후보 지역과 임무에 대한 고찰

이주희,류동영,Lee, Joohee,Rew, Dong-Young 한국우주과학회 2021 우주기술과 응용 Vol.1 No.3

우리나라는 2022년 8월 시험용 달 궤도선을 처음으로 달에 보낼 계획이다. 그리고 제3차 우주개발 진흥 기본계획을 통해서 밝힌 바에 따르면 이후 2030년 이전까지는 달 착륙선을 달에 보낸다는 계획이다. 달 착륙지역 선정에는 착륙선의 임무에 따라 적합한 착륙 지역이 달라질 수 있으며, 따라서 성공적인 달 탐사임무 설계를 위해서는 달 착륙지역에 대한 사전 연구가 반드시 필요하다. 본 논문에서는 2018년 NASA 워크숍에서 제안한 주요 달 착륙 후보지역에 대한 자료를 바탕으로 NASA의 MoonTrek을 이용하여 14개 제안 지역중 주요 지역의 특성을 분석하였다. 그리고 이런 지역이 향후 어떠한 달 착륙 임무에 적합한지 알아보았다. 또한 최근 달 착륙 국가들의 달 착륙 지역과 아르테미스(Artemis) 계획을 통해 달 남극의 중요성에 대해서도 알아 보았다. Korea plans to send a pathfinder lunar orbiter to the Moon for the first time in August 2022. And according to the 3rd Basic Plan for Space Development Promotion, the plan is to send a lunar lander to the Moon before 2030. The selection of the lunar landing area can be varied depending on the lunar lander's mission, therefore preliminary research on the lunar landing sites is essential for a successful lunar exploration mission design. This paper analyzed the characteristics of major regions among 14 proposed regions using NASA's MoonTrek based on the data on the candidate areas for the major moon landing proposed sites by the NASA workshop in 2018. And we looked into what kind of future moon landing missions are suitable for these areas. We also looked at the importance of lunar Antarctica area through the recent lunar landing areas of Moon landing countries and Artemis plan.