http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
旋削加工에서 極低溫 切削條件에 따른 切削特性에 關한 硏究
吳世憲,李小榮 한밭대학교 산업과학기술연구소 1994 논문집 Vol.2 No.-
In this study, the difficult cutting materials such as austenite type Stainless steel(STS304), SNCM220, STD61 and Carbon steel for machine structural use(SM45C), Aluminum alloy(Al2024) materials were cut in the cryogenic condition of -195℃ by the liquid nitrogen and the liquid nitrogen was sprayed on the cutting part to continue the low temperature during the cutting process. I compared the force to the cut the test materials and surface roughness in cutting between in room temperature and cryognic temperature. In the test, Cemented carbide tool(KTP10) was used to cut the test materials. The cutting force were measured by the tool dynamometer(TSM-ZMM) and multicorder(5L-3I), the surface roughness was measured by surface roughness measuring instrument(SURFCOM 300B).
오세헌,민택기 한국공작기계학회 2004 한국생산제조학회지 Vol.13 No.3
Generally, it is used the compensation spring to compensate the inaccuracy of screen image induced by thermal deformation in CRT monitor. Its mechanism is bi-metallic system made of heterogeneous metals and these is bonded by laser welding. But laser welding induces the non-uniform temperature distribution and locally residual stress is yielded by these temperature deviation. This paper studies residual stress of laser weldment using FEA and hole drilling method. The results are followed. In the case of heterogeneous materials weldment, higher residual stress induced in the weldment region of SUS 304 which have larger CTE than Xi 36 and residual stress on the middle of specimen is higher by 10.9% than that of its surface Measured residual stress of SUS 304 yield 481MPa and that of Ni 36 is 140.5MPa in the vicinity of the welding region. And the residual distribution is very similar in comparison with FEA result.
Carbamoylethyl Starch의 製造와 종이 製造時 添加效果에 관한 硏究
尹世永,崔正箕,鄭文箕,趙炳默,吳正壽 동국대학교 생명자원과학대학 연습림 1995 연습림논문집 Vol.- No.4
Recently, paper strength properties come up to be lowered by increasing ratio of utilization of recycling paper. In order to overcome these problems, strengthening agents which may cause enviromental problems have been used. Therefore, acrylamide was added to starch which is a cheap natural polymer, carbamoylethyl starch(CES) with high activity was prepared, and so the applicability as a paper additive was examined. The results are following; FT-IR spectra of CES of which degree of substitution was 0.25 showed strong C=O band at 1680㎝^-1 which corresponds the carbonyl group n amides(amide Ⅰ). Analysis of bravender viscosity showed that cooking start point of CES is 60℃ and instant viscosity is 830 B.U.(bravender unit). Effect of carbamoylethl DS on strength properties was resulted that CES of DS 0.20 appeared to be the best choice for making handsheets from KOCC with good overall strength properties, and it was selected as standard sample. Effect of pH on strength properties was obvious for their increasing values as decreasing pH. Also, a 5-fold increase in size rate as well as significant increase in wet-tensile strength were obtained in handsheets from KOCC by 3% wet-end addition of CES.
백롱민,박재현,김진환,백세민,오갑성,정연철 大韓成形外科學會 1993 Archives of Plastic Surgery Vol.20 No.5
The shape and contour of the upper third of the face is provided basically by the frontal bone. A relatively thin soft tissue coverage, which consists of the skin and frontalis muscle, readily shows subtle changes on the underlying frontal bone. The forehead represents the fortune of one's youth from the viewpoint of physignomy, and a broad forehead with minimal supraorbital bossing and round curvature is preferrd in the Orient. The forehead with a deficient, flat contour or asymmetry could be indicated for augmentation. The exact site and amount of augmentation are dicided preoperatively using clinical assessment, medical photographs, and cephalometric analysis. Hydroxyapatite(Pyrost), because of its nonresorbability, seems to have advantages over other alloplastic materials for forehead augmentation. From March 1989 to February 1992 forehead augmentation has been performed in 60 patients. Through a coronal incision, the dissection was carried over the periosteum to the supraorbital ridge and the lateral orbital rim. The subperiosteal pocket was made through a small incision, and was packed with Pyrost. When indicated, facial rhytidectomy, or reduction malar plasty was performed simultaneously. The result had been satisfactory and long lasting. There had been no implant shifting, infection, or bony erosion when examed from 1 year to 4 years after surgery.