http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
CMIP5 MME와 Best 모델의 비교를 통해 살펴본 미래전망
김병희(Byeong-Hee Kim),문혜진(Hyejin Moon),하경자(Kyung-Ja Ha) 한국기상학회 2015 대기 Vol.25 No.2
The changes in thermodynamic and dynamic aspects on near (2025~2049) and long-term (2075~2099) future climate changes between the historical run (1979~2005) and the Representative Concentration Pathway (RCP) 4.5 run with 20 coupled models which employed in the phase five of Coupled Model Inter-comparison Project (CMIP5) over East Asia (EA) and the Korean Peninsula are investigated as an extended study for Moon et al. (2014) study noted that the 20 models’ multi-model ensemble (MME) and best five models’ multi-model ensemble (B5MME) have a different increasing trend of precipitation during the boreal winter and summer, in spite of a similar increasing trend of surface air temperature, especially over the Korean Peninsula. Comparing the MME and B5MME, the dynamic factor (the convergence of mean moisture by anomalous wind) and the thermodynamic factor (the convergence of anomalous moisture by mean wind) in terms of moisture flux convergence are analyzed. As a result, the dynamic factor causes the lower increasing trend of precipitation in B5MME than the MME during the boreal winter and summer over EA. However, over the Korean Peninsula, the dynamic factor causes the lower increasing trend of precipitation in B5MME than the MME during the boreal winter, whereas the thermodynamic factor causes the higher increasing trend of precipitation in B5MME than the MME during the boreal summer. Therefore, it can be noted that the difference between MME and B5MME on the change in precipitation is affected by dynamic (thermodynamic) factor during the boreal winter (summer) over the Korean Peninsula.
김병희(Byeong-hee Kim),김헌영(Heon-young Kim),김호(Ho Kim),김광순(Kwang-soon Kim),강신일(Shin-ill Kang) 대한기계학회 2003 대한기계학회 춘추학술대회 Vol.2003 No.4
The hot embossing process has been mentioned as one of major nanoreplication techniques. This is due to<br/> its simple process, low cost, high replication fidelity and relatively high throughput. As the initial step of<br/> quantitating the embossing process , simple parametric study about embossing time have been carried out<br/> using high-resolution masters which patterned by the DRIE process and laser machining. Under the various<br/> embossing time, the viscous flow of thin PMMA films into microcavities during compression force has been<br/> investigated. Also, a study about simulating the viscous flow during embossing process has planned and<br/> continuum scale FDM analysis was applied on this simulation. With currently available test data and<br/> condition, simple FDM analysis using FLOW3D was made attempt to match simulation and experiment.
직접 가열방식에 의한 극세선의 직선화 및 전단 버의 최소화에 관한 연구
김병희(Byeong Hee Kim),김웅겸(Woong Kyum Kim),홍남표(Nam Pyo Hong),김헌영(Heon Young Kim),윤성만(Seong Man Yoon) 대한기계학회 2005 대한기계학회 춘추학술대회 Vol.2005 No.5
There are many ways about straightening process of the micro wire, such as simple tension, roll forming and pulling as soon as direct/indirect heating. In this study, we have developed a novel wire straightener which uses the direct heating method (DHM) for straightening the micro wire. In order to avoid the surface oxidization, we supplied the inert gas(Ar) during the heating process and examined the effect of gas flow rate. And we evaluated the burr height at the end of the wire which used the shearing machines. From various experiments and analyses, we could obtain fine straightness(? 1㎛/1000㎛), roundness(<±2㎛ /100㎛) and minimized the burr height when the tension is 500~600gf and the current is about 1.5A.
김한희(Han-Hee Kim),전은채(Eun-chae Jeon),최대희(Dae-Hee Choi),장웅기(Woong-Ki Jang),박용민(Yong-Min Park),제태진(Tae-Jin Je),최두선(Doo-Sun Choi),김병희(Byeong-Hee Kim),서영호(Young-Ho Seo) Korean Society for Precision Engineering 2015 한국정밀공학회지 Vol.32 No.1
Micro/nano patterns for optical concentration and diffusion have been studied in the various fields such as displays, optics, and sensors. Conventional micro patterns were continuous and linear shapes due to using linear-type light sources, however, recently non-continuous patterns have been applied as point sources are used for dot-type light sources such as LEDs and OLEDs. In this study, a hybrid machining technology combining an indentation machining method and an AAO process was developed for manufacturing the non-continuous micro patterns having nano patterns. First, mirror-like surfaces (R<SUB>a</SUB><20nm) of pure Aluminum substrates were obtained by optimizing cutting conditions. Then, The letter of ‘K’ consisting of the arrays of the micro patterns was manufactured by the indentation machining method which has a similar principle to indentation hardness testing. Finally, nano patterns were machined by AAO process on the micro patterns. Conclusively, a specific letter having nano-micro hybrid patterns was manufactured in this study.
김광수(Kwangsoo Kim),최종필(Jong Pil Choi),정창렬(Chang Ryeol Jeong),장재혁(Jae Hyeok Jang),전병희(Byeong Hee Jeon),김병희(Byeong Hee Kim) Korean Society for Precision Engineering 2008 한국정밀공학회지 Vol.25 No.1
In this paper, a three-dimensional computational fluid dynamic model of a proton exchange membrane fuel cell(PEMFC) with serpentine flow channel is presented. A steady state, single phase and isothermal numerical model has been established to investigate the influence of the GDL (Gas Diffusion Layer) parameters. The GDL is made of a porous material such as carbon cloth, carbon paper or metal wire mesh. For the simplicity, the GDL is modeled as a block of material having numerous pathways through which gaseous reactants and liquid water can pass. The porosity, permeability and thickness of the GDL, which are employed in the model parameters significantly affect the PEMFC performance at the high current region.