http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
12차 통신사 필담집의 특징-對禮餘藻의 주자학 담론을 중심으로-
구영진 열상고전연구회 2009 열상고전연구 Vol.29 No.-
1811년의 12차 통신사행은 조선시대 마지막 통신사로서 역지되고 축소된 와해와 변질의 통신사로, 혹은 믿음의 교류로, 반대로 비교린적 폐쇄적 교류로 다양하게 이해되었다. 필담집 「대례여조」는 사상적 변화 속에 새롭게 등장한 일본의 관정 주자학자들과 개국 이래 400년간 주자학의 적통임을 자부하던 조선의 사행원들 간의 필담 창화한 내용의 일본 측 기록이다. 「대례여조」에서 이들 간의 주자학 담론을 살핌으로 조일의 다른 함의의 주자학의 실상과 양국이 얻고자 한 바를 읽을 수 있으리라 생각하며 그것은 12차 통신사행의 특징을 읽는 한 방법이 될 것이다. 19세기초 마지막 통신사행의 주자학 담론에는 일본 측의 주자학으로의 변화를 천명함과 조선 측의 환영하는 태도로 우호적인 분위기와 공경과 신의의 공감대를 형성하고 있다. 그러나 주자학 담론에서 양측은 서로 다른 관심과 함의를 가지고 대화하고 있었다. 일본은 행동의 실제에 적용하는 문제에 관심을 드러내고 있었고 조선은 개인적 수기(修己)의 문제로 해명하고자 하는 태도를 나타내고 있었다. 즉, 조선은 주자학의 형이상학을 더 깊이 추구한 도덕론의 강조로 나아가고 일본은 주자학의 형이하학에 치중하여 사회적 윤리를 세우기 위한 치세론으로 나아간 주자학 담론의 장이었던 것을 알 수 있다. 이렇게 다른 주자학의 담론 가운데서 양측의 기대도 각자 다른 것이었다. 서로 다른 함의의 주자학 담론을 알아차린 조선 측에서는 굳이 지적하지 않고 조선의 주자학적 영향이 계속되기를 기대하고 있었고, 일본 측에서는 빈주읍양의 예로 접대하는데 주자학 담론을 활용함으로써 일본의 높아진 국체를 기대하고 있었음을 짐작할 수 있다.
구영진,이명현,윤석영,이윤주 대한금속·재료학회 2022 대한금속·재료학회지 Vol.60 No.4
3D printing technology has advanced rapidly over the last decade. However, for ceramic materials, drying and sintering steps are required after printing, and excessive shrinkage that occurs during these steps is a major factor that has hindered the development of the ceramic 3D printing technology. In this study, a non-sintering ceramic 3D printing method was developed using a hydraulic material to overcome the size deformation issue encountered during the post-processing of a scaffold-type printed green body. The deformation characteristics occurring during the curing process were confirmed. Tricalcium silicate (C3S) and tricalcium aluminate (C3A), which are well-known hydraulic materials, were selected. They were prepared into a printable paste by mixing with a viscous hydrophilic oil such as polyethylene glycol and polypropylene glycol, which helped the printout survive without collapse while it was cured. The scaffold was printed by Fused Deposition Modelling (FDM), which is the simplest and most economical printing method, and was cured by immersion in a water bath. The hydrated scaffold of the C3S/C3A mixture exhibited a smaller strain than the scaffold of the single materials, and the deformation amount depended on the printing direction. Remarkably, a scaffold with the smallest deformation, of less than 1%, and the highest compressive strength was obtained with a C3S/C3A mixing ratio of 65/35.
구영진,이윤주,이명현,윤석영 대한금속·재료학회 2022 대한금속·재료학회지 Vol.60 No.9
With the development of additive manufacturing technology, many types of materials are being utilized, and methods of printing the materials and characteristics of their hydration properties are being studied in the fields of construction and biotechnology. Tricalcium silicate (C3S), which is used as a cement material or biomaterial, is a representative hydraulic material. In previous research, scaffolds were printed via fused deposition modeling and the deformation properties during the hydration process of the printed scaffold were investigated. C3S, like ceramic materials, requires post-processing such as curing after printing, and volumetric deformation occurs during this process. Deformation information is very important to ensure the numerical value of the final product, as well as to suppress the possibility of deformation. In this study, silica, hydroxyapatite (HA), and alumina were mixed with three types of fillers to print a C3S support, which was then cured through a two-step process. In this process, HA and silica, which have good hydrophilicity, exhibited high strength due to the suppression of scaffold deformation. It was confirmed that the smaller the particle size, the more effective it was in obtaining a stable hydrated print.