요양보호사 교육생을 위한 기본심폐소생술 교육프로그램 개발 및 효과

이성희,최정실,Lee, Sung Hee,Choi, Jeong Sil 한국가정간호학회 2016 가정간호학회지 Vol.23 No.2

Purpose: This study set out to use a one-group pretest-posttest experimental design to develop a highly motivating CPR program for help care workers who lack CPR education, and to evaluate its effects on their knowledge about program application, attitude, and self-efficacy. Methods: For this purpose, 140 questionnaires were administered to subjects who underwent training at an educational institution for care workers in S city and G province. The program was developed from April, 25 to May, 15 in 2016, and the evaluation period was from May to July, 15. The collected data were analyzed through SPSS version 23, and a paired t-test was conducted. Results: The program spanned 240 minutes, including 80 minutes on theoretical education and 160 minutes on practical education. Knowledge of CPR in the post-test proved to be higher than that in the pre-test, from 6.4 to 9.2 (t=-15.72, p<.001),; the score on attitude increased from 38.4 to 41.7 (t=-5.89, p<.001),; and self-efficacy increased from 41.0 to 66.7 (t=-21.83, p<.001). Conclusion: The basic CPR education program emphasizing motivation was effective for the care worker trainees and could be used for other curriculum by expanding the scope of the subject.

대형 후육 LH형 탄성구조 프레임의 사출성형 최적화에 관한 연구

이성희,Lee, Sung-Hee 한국금형공학회 2022 한국금형공학회지 Vol.16 No.1

In the present study, the injection molding optimization of a large thick LH type elastic frames for the reduction of warpage was performed. Two kinds of fine and coarse finite element models were prepared to investigate the efficiency of analysis time and quality on simulation results. In order to derive injection molding conditions that can minimize distortion of parts, it was investigated that the effects of mold temperature, resin temperature, injection time, hold pressure switching time, holding pressure and the hold time on deformation characteristics using the design of experiments. The main influential factors on the warpage were found from the optimization simulation and the geometry data of the warpage result was converted into an initial model for injection simulation. It was shown that a coarse model with good mesh quality could be adapted for mold design since the total analysis time using the proposed model was reduced to 1/10. The suggested inversed warpage model produced the best minimized result of warpage.

블로그 게시물에 나타난 수도권 보전지역 및 자연자원의 분포 및 특성

이성희,손용훈,Lee, Sung-Hee,Son, Yong-Hoon 한국조경학회 2022 韓國造景學會誌 Vol.50 No.5

This study aimed to evaluate the awareness of conservation areas and green resources and analyze their characteristics by utilizing accumulated blog data created for specific places and objects. Among all the conservation areas and resources located in the Seoul metropolitan area, places that can be evaluated were classified, and sites were evaluated by dividing them into ten categories based on the number of blog posts written. As a result of the study, the users' awareness of forests was the highest, and the awareness of conservation areas and green resources was higher in urban areas than suburban areas. The result shows that the conservation areas and green resources located around the metropolitan area serve as natural tourist destinations while being the object of conservation for users. In addition, these results are in the same vein as the research results in domestic and foreign studies on the importance of ecosystem services in urban areas. Unlike existing research methods, this study is meaningful in that it identified the level of user awareness through social media analysis and applied it to evaluating conservation areas and green resources. It can be used as basic data to prepare a management plan considering public interest and awareness or to establish a development plan to increase awareness. In addition, the cumulative amount of blog content used in the study is meaningful in that it can identify and monitor users' interest in the space. However, it was not possible to examine the contents of each blog in detail because it was evaluated based on the amount of social media content. In addition, in the case of conservation areas and green resources, it is necessary to review and supplement the evaluation contents by adding keyword analysis and content analysis for the site to be evaluated as content other than the pure viewpoint of users may be mixed with development issues.

현대문학 : 이청준의 「매잡이」연구 -랜서의 시점이론을 중심으로

이성희 ( Sung Hee Lee ) 문창어문학회 1999 문창어문논집 Vol.36 No.-

The purpose of this subject is to prove Lee tried to describe that the point of view concerns not only how to express, based on Lancer`s theory, but also how the author illustrates his theme. Lancer`s theory explains that the point of view, although it is a matter of expression, is influenced by author`s ideology. In 「Hawker」, the hero Tae-joon Min incarnates Lee`s ideology, formulating the main stream. Lee`s intention to stay away from readers is ultimately premised on his own authorization. This is why I selected 「Hawker」 to clarify Lee`s authorization and the conclusion is as follows. Lancer`s theory implies the structure of narrative, point of view and the authorization are on the same boat. I studied how the implication reflects the authorization through the structure-point analysis.

토양 중 PBDEs와 PCBs의 농도분포

이성희,조기철,여현구,Lee, Sung-Hee,Cho, Ki-Chul,Yeo, Hyun-Gu 한국환경보건학회 2009 한국환경보건학회지 Vol.35 No.6

Polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) were measured in soil samples of Ansung in Kyonggi-province to investigate concentration distribution of PBDEs and PCBs. The 10 soil samples were collected using a stainless steel hand-held corer that was cleaned before and after each sample using hexane. Total concentration of PBDE and PCBs were 2,205.3 and 348.1 pg/g dry weight (DW) in soil sample, respectively. BDE-209 showed as the most abundant congener in soil samples which was related to imported amount and usage amount of deca-BDE technical mixture in Korea. Also, BDE-99, BDE-47, BDE-100 deposition in soil sample was higher than other congeners and was related to the imported and usage amount reported for penta-BDE technical mixture in Korea. Correlation coefficient between PBDE contribution and technical mixture formulation (Bromokal 70-5DE) were significant (r=0.91, p<0.01) which suggests the influence of sources in this technical mixtures.

블로그 데이터 감성분석을 통한 북한산둘레길 구간별 선호도 평가

이성희,손용훈,Lee, Sung-Hee,Son, Yong-Hoon 한국조경학회 2021 韓國造景學會誌 Vol.49 No.3

This study aimed to evaluate preferences of Bukhansan dulegil using sentiment analysis, a natural language processing technique, to derive preferred and non-preferred factors. Therefore, we collected blog articles written in 2019 and produced sentimental scores by the derivation of positive and negative words in the texts for 21 dulegil courses. Then, content analysis was conducted to determine which factors led visitors to prefer or dislike each course. In blogs written about Bukhansan dulegil, positive words appeared in approximately 73% of the content, and the percentage of positive documents was significantly higher than that of negative documents for each course. Through this, it can be seen that visitors generally had positive sentiments toward Bukhansan dulegil. Nevertheless, according to the sentiment score analysis, all 21 dulegil courses belonged to both the preferred and non-preferred courses. Among courses, visitors preferred less difficult courses, in which they could walk without a burden, and in which various landscape elements (visual, auditory, olfactory, etc.) were harmonious yet distinct. Furthermore, they preferred courses with various landscapes and landscape sequences. Additionally, visitors appreciated the presence of viewpoints, such as observation decks, as a significant factor and preferred courses with excellent accessibility and information provisions, such as information boards. Conversely, the dissatisfaction with the dulegil courses was due to noise caused by adjacent roads, excessive urban areas, and the inequality or difficulty of the course which was primarily attributed to insufficient information on the landscape or section of the course. The results of this study can serve not only serve as a guide in national parks but also in the management of nearby forest green areas to formulate a plan to repair and improve dulegil. Further, the sentiment analysis used in this study is meaningful in that it can continuously monitor actual users' responses towards natural areas. However, since it was evaluated based on a predefined sentiment dictionary, continuous updates are needed. Additionally, since there is a tendency to share positive content rather than negative views due to the nature of social media, it is necessary to compare and review the results of analysis, such as with on-site surveys. 본 연구는 탐방객이 자유롭게 서술한 블로그 텍스트 데이터를 자연어 처리 기술 중 하나인 감성분석을 활용하여 북한산둘레길의 선호도를 평가하고, 선호 요인과 비선호 요인을 도출하는 것을 목적으로 하였다. 이에 2019년 1년 동안 작성된 블로그를 수집하고 21개 둘레길 구간별 텍스트에 나타난 긍정 및 부정 감성 단어 도출을 통해 감성점수를 산출하였다. 이후 내용분석을 통해 탐방객이 어떤 요소로 인해 구간을 선호하거나 선호하지 않는지 파악하였다. 북한산둘레길에 대해 작성된 블로그에서는 긍정적인 단어가 평균적으로 약 73% 출현하고 있었고, 각 구간별 게시물의 감성 극성 비율에서도 긍정적인 문서의 비율이 부정적인 문서의 비율보다 높았다. 이를 통해 탐방객은 북한산둘레길에 대하여 대체로 긍정적으로 인식하고 있는 것으로 나타났다. 그럼에도 감성점수를 도출한 결과, 21개 둘레길 구간에서는 선호하는 구간과 선호하지 않는 구간이 존재하고 있었다. 선호 구간과 비선호 구간에 대해 탐방객은 난이도가 낮고 부담 없이 걸을 수 있는 구간을 선호하고 있었고, 경관에 대한 여러 요소(시각, 청각, 후각 등)가 조화롭고 계절감이 뚜렷해 다양한 경관이 연출되는 곳, 경관 시퀀스의 변화가 존재하는 구간을 선호하는 것으로 나타났다. 또한 탐방객은 전망대, 조망점 등의 뷰포인트 유무를 둘레길에서의 주요 요소로 인식하고 있었고, 접근성이 우수하고 안내판 등 정보 제공이 원활하게 이뤄지는 구간에 대해 선호도가 더 높은 것을 알 수 있다. 반면, 도로와 인접함에 따라 발생되는 주변 소음과 과도한 시가지 비율, 구간별 난이도 불균형 등으로 인한 둘레길 동선 불만족이 비선호 요인으로 크게 작용하고 있었으며, 경관 단절 및 구간에 대한 정보 부족 등이 선호도를 떨어트리는 원인으로 나타났다. 본 연구의 결과는 국립공원뿐만 아니라 근교 산림 녹지 관리에 있어서 둘레길 정비 및 개선방안 마련에 활용될 수 있으며, 연구에 활용된 감성분석은 자연지역에 대한 실제 이용자들의 반응을 지속적으로 모니터링 할 수 있다는 점에 의의가 있다. 다만 사전에 정의된 감성사전을 기반으로 평가하였기에 지속적인 사전 업데이트가 필요하다. 또한 소셜미디어 특성상 부정적인 견해보다는 긍정적인 내용을 공유하는 경향이 존재하기 때문에, 현장 설문조사 등의 분석 결과와 비교, 검토하는 작업이 필요하다.

공적(公的)관리에서의 참여형 관개관리(PIM) 모델

이성희,김태철,Lee, Sung-Hee,Kim, Tai-Cheol 한국농공학회 2011 한국농공학회논문집 Vol.53 No.3

There was a transition from participatory irrigation management (PIM) to public irrigation management (PubIM) in Korea when Korea Rural corporation and Community (KRC) merged with Farm Land Improvement Associations (FLIAs), which had managed 60 % of irrigation areas. While making a number of achievements, some problems occurred in the public irrigation management, such as lack of farmers' participation, increased amount of water usage, and elevating operating costs. Accordingly, this paper suggested ways to increase efficiency in water usage and reduce operating costs under the public management through the motive power of farmers participation. First, WUGs replaced the discarded water management committee should be reorganized to revive the concept of PIM in the form of autonomously reinforced one and the roles and functions of WUGs and the board of representatives should be strengthened. The member of new type of WUGs should participate in the national and regional water management committees as a stakeholder of irrigation water user. And also new type of WUGs initiates not only the management of irrigation water but also the management of irrigation water quality and non-point source pollution in the watersheds. Those additional activities of WUGs should be properly compensated. Second, subsidies (direct payments) should be provided to faithful farmers as an incentive for their labor supply. Third, water fees could be charged to large scale agriculture companies. Fourth, professional managers could be hired, management targets would be adjusted, and incentives should be offered. These efforts are expected to improve the irrigation management by encouraging farmers' participation under public system.

조립각형 CFT 기둥의 용접크기 결정을 위한 수압실험 및 해석

이성희,김선희,김영호,최성모,Lee, Seong-Hui,Kim, Sun Hee,Kim, Young Ho,Choi, Sung Mo 한국강구조학회 2009 韓國鋼構造學會 論文集 Vol.21 No.5

콘크리트 충전강관에 사용되는 강관의 제작법은 재단된 4장의 플레이트를 모서리에서 용접하는 일반강관 제작법과, ㄷ형으로 절곡성형과정을 거쳐 2-Seam으로 용접하는 제작방법, 그리고 원형강관을 압축하여 4각형태로 만드는 방법등이 일반적으로 사용되며, 강관제작에 사용되는 용접방법과 용접량의 선택은 강관 제작비용에 큰 부분을 차지하고 있다. 새로운 제작형식으로 개발된 각형강관은 4장의 플레이트를 ㄱ형으로 절곡성형한 후 강관 폭의 중앙에서 4-Seam Flare 용접하는 방식이다. 본 연구에서는 새로운 제작형식의 CFT 각형 기둥에 대하여 용접량 평가를 위한 실험방법을 제시하고, 강관 제작법, 강관두께 및 용접량을 변수로 총 6개의 실험체를 제작하여 구조실험 및 해석을 수행하여 강관내부의 수압에 따른 강관의 거동을 평가하였다. There are three main production processes in the manufacture of concrete-filled square steel columns. The first process is known as the 'box-type process' or 'four-seam method,' wherein four beams are welded together at the seams. The second is the 'cold-forming process' or 'two-seam method,' wherein the seams of two channel beams are welded together. The third is the 'pressing process' or 'one-seam method,' wherein a circular column is pressed until it becomes a square column. In calculating the production cost for the making of a steel tube, it is very important to consider the welding process to be used and the desiredthickness of the steel tube, such as a square column that was developed under a new method, formed through the four-seam flare welding method at the center of the steel column width, following the L-shape formation. Certain tests were suggested in this study to evaluate the welding amount of concrete-filled square steel columns. With the parameters of the production method of a square steel column, the thickness of the steel square columns, and the welding amount, six specimens were produced. A structural test and finite-element analysis were conducted to assess the behavior of the steel column according to the water pressure inside the steel columns.

다공성 임플란트 제조를 위한 3D 프린팅 응용 금형기술

이성희,김미애,윤언경,이원식,Lee, Sung-Hee,Kim, Mi-Ae,Yun, Eon-Gyeong,Lee, Won-Sik 한국금형공학회 2017 한국금형공학회지 Vol.11 No.1

In this study, the mold technology for manufacturing of porous implant was investigated. Firstly, we considered the concept of insert molding technology with 3D printing of porous inert part. The part on implant was designed in the end region of the implant. And then main implant bodies were manufactured using conventional machining method. The other porous parts were designed and optimized with molding simulation. As the feature size of porous implant was so small that perfect feature of it using 3D printing technology could not be obtained. So, we proposed another scheme for manufacturing of the porous implant in the replace of the former approach. Polymer mold cores with 3D printing technology were considered. The effects of addictive manufacturing process parameters on the properties of mechanical and dimensional accuracy were investigated. Direct 3D printed polymer mold cores were designed and manufactured under the simulation of thermal and molding analysis. It was shown that 3D printed mold core with polymer could be adapted to the injection molding for porous implant.

리저버 탱크의 Die Turning Injection 적용을 위한 Multi-field CAE 해석

이성희,Lee, Sung-Hee 한국금형공학회 2021 한국금형공학회지 Vol.15 No.1

In this study, die turning injection(DTI) mold design for manufacturing reservoir fluid tanks used for cooling in-vehicle batteries, inverters, and motors was conducted based on multi-field CAE. Part design, performance evaluation, and mold design of the reservoir fluid tank was performed. The frequency response characteristics through modal and harmonic response analysis to satisfy the automotive performance test items for the designed part were examined. Analysis of re-melting characteristics and structural analysis of the driving part for designing the rotating die of the DTI mold were performed. Part design was possible when the natural frequency performance value of 32Hz or higher was satisfied through finite element analysis, and the temperature distribution and deformation characteristics of the part after injection molding were found through the first injection molding analysis. In addition, it can be seen that the temperature change of the primary part greatly influences the re-melting characteristics during the secondary injection. The minimum force for driving the turning die of the designed mold was calculated through structural analysis. Hydraulic system design was possible. Finally, a precise and efficient DTI mold design for the reservoir fluid tank was possible through presented multi-field CAE process.