층층나무 잎의 Phenol성 성분 (I)

이동호,이승호,정시련,노재섭,이경순,Lee, Dong-Ho,Lee, Seung-Ho,Chung, See-Ryun,Ro, Jai-Seup,Lee, Kyong-Soon 한국생약학회 1995 생약학회지 Vol.26 No.4

Twelve phenolic components were isolated from the aqueous acetone extract of the leaf of Cornus controversa H. (Cornaceae). On the basis of chemical and spectroscopic evidence, the structures of these components were established as gallic acid, $1-O-galloyl-{\beta}-{_D}-glucose$, $1,6-di-O-galloyl-{\beta}-{_D}-glucose$, $1,2,3-tri-O-galloyl-{\beta}-{_D}-glucose$, $1,2,6-tri-O-galloyl-{\beta}-{_D}-glucose$, 3,4,6-tri-O-galloyl ${_D}-glucose$, eugeniin, gemine D, quercetin, quercitrin, hyperoside and rutin.

초소형 수중 음향 시스템 모듈의 저잡음 설계 방법

이동호,신영산,송진호,위재경,이정민,설재수,Lee, Dong-Ho,Shin, Young-San,Song, Jin-Ho,Wee, Jae-Kyung,Lee, Jeong-Min,Seol, Jae-Soo 한국음향학회 2012 韓國音響學會誌 Vol.31 No.5

본 논문에서는 다중 전압을 사용하는 초소형 시스템 구성 및 모듈 설계 방법론을 제시한다. 특히 잡음에 취약한 아날로그 IC의 특성을 개선하기 위한 PDN 구성 방법과 필터 구성 방법에 중점을 두어 설계하였다. 이에 제작된 모듈은 고전압에 의한 잡음을 방지하기 위해 공급 전원별로 접지면을 분할하고, 이를 공통 접지면으로 구성하기 위해 필터를 연결하였으며, via stitching 기법을 사용하였다. 이를 본 논문에서는 PDN 구조를 Lumped 모델로 구성하여 시뮬레이션을 통해 분석하고, 측정을 통해 확인하였다. 시뮬레이션 결과 4.7 uH의 Inductor를 연결하였을 때, 공통 접지면을 사용했을 때보다 -7 dB의 잡음 감소 효과를 확인할 수 있었고, 측정 결과 약 12 %가 감소하였음을 확인할 수 있었다. This paper suggest configuration method of small-size system and design method of module using multi power. In particular module designed to focus on PDN(Power Distribution Network) and filter configuration method to improve the characteristics of noise sensitive analog IC. For the prevention of high-voltage noise, manufactured module is used the ground-isolated technique and via stitching, and is connected grounds with a series of filters. In this paper, so we analyzed PDN structure through the simulation using lumped modeling and confirmed through measurement. Simulation results, when connecting 4.7uH inductor, we made certain that noise of -7dB decreases much more than when it did not. And it was confirmed 12% less than Background Noise.

서울 에어쇼'96 평가와 항공산업 발전 방안

이동호,Lee, Dong-Ho 한국항공우주산업진흥협회 1996 航空宇宙 Vol.46 No.-

성황리에 막을 내린 서울에어쇼96은 국민적 인식제고와 우리나라의 항공우주산업을 전세계에 알린 의미있는 행사였다. 그러나 처음 치른 행사, 노하우부족 등으로 많은 문제점이 발생되었으며 이에 따른 대안들이 98년 행사에 100% 반영되어야 할 것이다. 하지만 바늘과 실의 관계처럼 연관되어야 할 것이 바로 우리 항공우주산업의 발전인 것이다. 이글에서는 서울에어쇼''''96을 평가하고 이와함께 우리나라 항공우주산업 도약의 전기를 마련할 수 있는 대안을 제시해 보았다.

일관성있고 체계적인 지원 육성

이동호,Lee, Dong-Ho 한국전자정보통신산업진흥회 1981 電子振興 Vol.1 No.4

치과용 콘빔 CT를 이용한 상악 정중과잉치의 3차원 분석

이동호,이재서,윤숙자,강병철,Lee, Dong-Ho,Lee, Jea-Seo,Yoon, Suk-Ja,Kang, Byung-Cheol 대한영상치의학회 2010 Imaging Science in Dentistry Vol.40 No.3

Purpose : This study was performed to analyze the position, pattern of impacted mesiodens, and their relationship to the adjacent teeth using Dental cone-beam CT. Materials and Methods : Sixty-two dental cone-beam CT images with 81 impacted mesiodenses were selected from about 2,298 cone-beam CT images at Chonnam National University Dental Hospital from June 2006 to March 2009. The position, pattern, shape of impacted mesiodenses and their complications were analyzed in cone-beam CT including 3D images. Results : The sex ratio (M : F) was 2.9 : 1. Most of the mesiodenses (87.7%) were located at palatal side to the incisors. 79% of the mesiodenses were conical in shape. 60.5% of the mesiodenses were inverted, 21% normal erupting direction, and 18.5% transverse direction. The complications due to the presence of mesiodenses were none in 43.5%, diastema in 19.4%, tooth displacement in 17.7%, delayed eruption or impaction in 12.9%, tooth rotation in 4.8%, and dentigerous cyst in 1.7%. Conclusions : Dental cone-beam CT images with 3D provided 3-dimensional perception of mesiodens to the neighboring teeth. This results would be helpful for management of the impacted mesiodens.

정책정보 2 - 식품공전 해설과 식품 기준.규격 선진화 계획

이동호,박재석,박선희,Lee, Dong-Ho,Park, Jae-Seok,Park, Seon-Hui 한국식품산업협회 2010 좋은식품 Vol.214 No.-

멀티 세그먼트 곱셈 기반 저비용 타원곡선 암호 프로세서

이동호,LEE Dong-Ho 대한전자공학회 2005 電子工學會論文誌-SD (Semiconductor and devices) Vol.42 No.8

본 논문에서는 효율적인 $GF(2^m)$ 멀티 세그먼트 곱셈 연산 구조를 제안하고 제안된 구조의 타원곡선 암호 프로세서 설계 응용을 연구한다. 제안된 멀티 세그먼트 곱셈 연산 구조는 유한체 크기 m에 비하여 아주 작은 워드 조합 곱셈기를 이용하여 부분곱을 계산하고 거의 모든 내부 버스는 워드 크기이며 m 비트 멀티플렉서와 m 비트 레지스터를 하나만 사용한다. 따라서 조합 곱셈기의 워드 크기 w를 줄이고 세그먼트 수 k를 크게 하여 전체 데이터패스 자원 사용량이 최소화할 수 있다. 제안된 곱셈기는 디지트 시리얼 곱셈기로 구현된 ECC 프로세서와 비교할 때 이론적으로 자원 효율성이 우수하다 암호 프로세서의 자원 사용량은 구현에 필요한 기본 하드웨어 요소 수뿐만 아니라 구성 요소들의 배치와 연결 상태에도 의존한다. 제안된 프로세서의 실질적인 자원사용량을 디지트 시리얼 곱셈기 기반 암호 프로세서와 비교하기 위하여 두 종류의 프로세서를 FPGA 상에 구현하였다. 실험 결과로 제안된 멀티 세그먼트 곱셈기 기반 EU 프로세서는 유사한 성능을 가지는 디지트 시리얼 곱셈기 기반 EU 프로세서보다 자원 사용면에서 2배 정도 우수함을 보였다. In this paper, we propose an efficient $GF(2^m)$ multi-segment multiplier architecture and study its application to elliptic curve cryptography processors. The multi-segment based ECC datapath has a very small combinational multiplier to compute partial products, most of its internal data buses are word-sized, and it has only a single m bit multiplexer and a single m bit register. Hence, the resource requirements of the proposed ECC datapath can be minimized as the segment number increases and word-size is decreased. Hence, as compared to the ECC processor based on digit-serial multiplication, the proposed ECC datapath is more efficient in resource usage. The resource requirement of ECC Processor implementation depends not only on the number of basic hardware components but also on the complexity of interconnection among them. To show the realistic area efficiency of proposed ECC processors, we implemented both the ECC processors based on the proposed multi-segment multiplication and digit serial multiplication and compared their FPGA resource usages. The experimental results show that the Proposed multi-segment multiplication method allows to implement ECC coprocessors, requiring about half of FPGA resources as compared to digit serial multiplication.

환형 캐스케이드 내 고정된 터빈 블레이드 및 슈라우드에서의 열/물질전달 특성 (II) - 끝단 필 슈라우드 -

이동호,조형희,Lee Dong-Ho,Cho Hyung Hee 대한기계학회 2005 大韓機械學會論文集B Vol.29 No.4

Experiments were conducted in a low speed stationary annular cascade to investigate local heat transfer characteristics on the tip and shroud and the effect of inlet Reynolds number on the tip and shroud heat transfer. Detailed mass transfer coefficients on the blade tip and the shroud were obtained using a naphthalene sublimation technique. The turbine test section has a single stage composed of sixteen guide vanes and blades. The chord length and the height of the tested blade are 150 mm and about 125 mm, respectively. The blade has flat tip geometry and the mean tip clearance is about $2.5{\%}$of the blade chord. The inlet flow Reynolds number based on chord length and incoming flow velocity is changed from $1.0{\times}10^{5}\;to\;2.3{\times}10^{5}.$ to investigate the effect of Reynolds number. Flow reattachment after the recirculation near the pressure side edge dominates the heat transfer on the tip surface. Shroud surface has very intricate heat/mass transfer distributions due to complex flow patterns such as acceleration, relaminarization, transition to turbulent flow and tip leakage vortex. Heat/mass transfer coefficient on the blade tip is about 1.7 times as high as that on the shroud or blade surface. Overall averaged heat/mass transfer coefficients on the tip and shroud are proportional to $Re_{c}^{0.65}\;and\;Re_{c}^{0.71},$ respectively.

치과용 임플란트 주위 열손 결손에 대한 차폐막의 유도조직재생에 관한 연구

이동호,최상묵,Lee, Dong-Ho,Choi, Sang-Mook 대한치주과학회 1995 Journal of Periodontal & Implant Science Vol.25 No.2

The purpose of this study was to evaluate a new biodegradable membrane - atelocollagen as a guided tissue regeneration barrier on the dehiscence defects adjacent to the dental implants. 3 beagle dogs were selected for this study and all the mandibular premolars($P_1,P_2,P_3&P_4$) were extracted. Twelve weeks after the extraction, the edentulous ridges were formed to be placed the titanium plasma-sprayed IMZ implants. Four implant osteotomies were performed on each side of the mandible. The osteotomies were placed facially in the edentulous ridges to approximate an actual dehiscence defect as closely as possible, The standardized dehiscence defects were created 3 mm in width and 4 mm in height by osteotomy. A total 24 implants were placed. e-PTFE, ateloco11agen and $Collatape^{(R)}$ were placed to cover the defects and the one defect served as a control, not covered any membrane. By random selection, three dogs were sacrificed at 2 weeks, 4weeks and 8 weeks after fixation with 3% glutaraldehyde. A week before sacrificing, 8-week dog was infused intravenously with oxy-tetracycline 30mg/kg. The left mandibular blocks were used for full decalcified histologic preparation and the right mandibular blocks were selected for undeca1cified preparation, At 2 weeks, the regenerated bone of e-PTFE and atelocollagen groups appeared to be more dense than other groups and the percentage of bone defect fill was highest for e-PTFE and follwed by ateloco1lagen group. However, the $Collatape^{(R)}$ and control groups showed a little new bone formation. $Collatape^{(R)}$ was almost degraded within 2 weeks. At 4 weeks, the regenerated new bone were much greater and denser than at 2 weeks for e-PTFE and ateloco11agen group. Although a part of atelocollagen bagan to be degraded at the margin and surrounded by foreign body giant cells related to foreign body reaction, it was generally intact and the regenerated new bone was shown much more than at 2 weeks. The amount of new bone in $Collatape^{(R)}$ and control groups at 4 weeks were similar to that of 2 weeks group. At 8 weeks, the regenerated bone was matured and observed along the implant fixture. Direct new bone formation and calcium deposits beneath the e-PTFE were observed. No further bone growth was seen in the $Collatape^{(R)}$ and control groups. In reflected fluoromicrcocopic observation, the osteogenic activity was pronounced between e-PTFE membrane and the old bone. High osteogenic activity was also observed in atelocol1agen group. This study suggested that the ateloco11agen as well as e-PTFE could be used for guided tissue regeneration on dehiscence defects adjacent to the dental implants. But the $Collatape^{(R)}$ was completely resorbed within 2 weeks and was not a suitable membrane for guided bone regeneration.

변형된 4스텝 써치를 이용한 블럭정합 움직임 추정 및 보상 알고리즘의 VLSI 구조 설계

이동호,Lee, Dong-Ho 대한전자공학회 1998 電子工學會論文誌, S Vol.s35 No.9

본 논문에서는 기존 고속 블럭 알고리즘보다 성능이 우수하고 하드웨어 구현에 적합한 새로운 MFSS(Modified Four-Step Search) 알고리즘을 제안한다. 제안하는 알고리즘의 추정 과정은 일정한 규칙을 갖기 때문에 하드웨어 구현에 적합하고, 모의실험을 통해 거의 FS(Full Search) 성능에 근접할 정도로 기존의 고속 움직임 추정 알고리즘보다 성능의 우수함을 확인하였다. 본 논문에서는 이러한 MFSS(Modified Four-Step Search) 움직임 추정 및 보상기 설계에서 중요한 고려 사항은 설계 결과의 하드웨어적인 크기와 출력이 나오기 까지의 필요한 지연 시간인데, 본 논문에서는 9개의 PE(Process Element)만을 이용하여 구현함으로써 전체 로직의 양을 최적화 하였고, 움직임 추정기와 보상기를 결합함으로써 메모리를 공유하고 필요한 지연시간도 줄이는 구조를 제안한다. This paper proposes a new fast block-matching algorithm, named MFSS(Modified Four-Step Search) algorithm, which has better performance and is more adequate for hardware realization than the existing fast algorithms. The proposed algorithm is suitable for hardware realization since it has a unique regularity during the search procedure. It is shown from simulation results that its performance is close to that of FS(Full Search) algorithm. This paper also proposes a VLSI architecture and presents some design results of a motion estimator and compensator which adopted the MFSS algorithm. The important aspects considered in designing a motion estimator and compensator are hardware complexity of design results, and total delay needed to generate the motion compensated data after finding the motion vectors. Hardware complexity is minimized by using just nine PE(Process Element)'s, and total delay is minimized by sharing search memory of the motion estimator and compensator.