소아의 단순성 비만증에 의한 지방간의 진단: ALT치와 복부 전산화단층촬영 및 간생검 소견간의 상관관계

이성희,김화중,오재철,한혜정,김희섭,차한,박호진,신미경,이민진,이상천,Lee, Seong-Hee,Kim, Hwa-Jung,Oh, Jae-Cheol,Han, Hae-Jeong,Kim, Hee-Sup,Tchah, Hann,Park, Ho-Jin,Shin, Mi-Keong,Lee, Min-Jin,Lee, Sang-Chun 대한소아소화기영양학회 1999 Pediatric gastroenterology, hepatology & nutrition Vol.2 No.2

목 적: 소아비만의 중요한 합병증 중 하나인 지방간을 진단함에 있어 ALT치와 CT 및 간생검 소견간의 상관관계를 살펴봄으로써, 선별검사로서 ALT치의 유용성과 확진검사로서 CT 및 간생검의 필요성을 알아보고자 한다. 대상 및 방법: 1990년 3월부터 1997년 12월까지 서울적십자병원 소아과에 내원하여 단순비만으로 진단 받은 78명 중 지방간 진단을 위해 CT를 실시한 26명을 대상으로 하였으며, 생화학검사 중 지방간의 선별검사로서 보다 특이성이 높은 ALT치가 지나치게 높거나 비만도가 심한 비만아들 중 15례에서 간생검을 실시하였다. 이들을 ALT치에 따라 3개 군으로 분류하고 각 군별로 신체계측지수, CT 및 간생검상 지방침착도 간의 상관관계를 비교 분석하였다. 결 과: 1) ALT치와 신체계측지수간의 상관관계: 대상 비만아 26례 중 ALT치는 17례(63.4%)에서 이상 상승(>30 IU/L)되었으나, ALT치의 상승과 신체계측지수들(비만도, RI, BMI, 체지방률) 간에는 유의한 상관관계가 없었다(p>0.05) 2) CT상 지방침착도와 ALT치 및 신체계측지수 간의 상관관계: 26례 중 13례(50%)에서 CT상 정상이었고, 나머지 13례는 정도의 차이는 있으나 모두 간음영이 증가된 지방간 소견을 보였다. CT상 지방간의 정도와 ALT치의 상승간에는 유의한 상관관계가 있었으나(p=0.01), 신체계측지수와는 유의한 상관관계가 없었다(p>0.05). 3) 간 생검상 지방간의 정도와 비만도, ALT치와의 상관관계: 26례 중 15례에서 간 생검을 실시한 결과, 1례에서 정상이었고 나머지 14례에서 모두 지방간 소견을 보였다. 그러나 간 생검상 정상인 1례는 고도비만이었으나 ALT치는 정상치였고, 중등도의 지방간 소견 보인 3례 중 1례는 고도비만이었음에도 ALT치는 정상이었으며 2례는 ALT치가 정상이거나 약간 증가하였으며, 심한 지방간 소견 보인 9례 중 1례는 경한 비만이었으나 ALT는 158 IU/L로 심한 상승을 보였다. 간 생검상 지방간인 14례를 지방침착도에 따라 3개 군으로 분류하여 비만도와 ALT치를 비교분석한 결과 비만도와 간 생검 소견간에는 유의한 차이가 없었으나(p>0.05), ALT치와 간 생검상 지방간의 정도간에는 유의한 차이가 있었다(p=0.01). 4) CT와 간 생검 소견간의 상관관계: 26례 중 15례에서 CT와 간 생검 모두를 시행한 결과, CT상 6례는 정상이었고, CT상 지방간 소견 보인 9례에서는 간의 지방침착도에 따른 음영의 변화를 기준으로 한 CT소견과 간 생검상 지방침착도간에 유의한 상관관계를 보였다(r=0.6094). 결 론: 최근 소아비만이 급증 추세에 있고 그에 따른 여러 가지 합병증들은 물론 성인비만으로 이행될 수 있으므로 학교보건 등을 통해 경각심을 높이도록 해야 하며, 특히 비만에 따른 지방간을 진단하기 위한 선별검사인 ALT치 등 생화학적인 간 기능 검사로는 간 손상 정도를 평가할 수 없기 때문에 보다 저비용이며 비침습적인 초음파검사를 적극 활용토록 하고 선별검사 등으로 선정된 고위험군에 대해서는 간 생검을 통해 간 손상 정도를 정확히 평가하고 지속적으로 추적 관리해야 할 것이다. Purpose: The purpose of our study is to provide useful information for diagnostic methods of fatty liver by childhood simple obesity and to provide correlation between serum alanine aminotransferase (ALT) for screening test and abdominal computerized tomography (CT) and liver biopsy for confirmative diagnostic methods of fatty liver. Methods: Among 78 obese childrens who visited our hospital, CT was carried out in 26 childrens. Of these, liver biopsy was carried out in 15 childrens who had high obesity index or severe elevated ALT. Based on the level of serum ALT, 26 cases were classified into 3 groups, and compared with physical measurements and degree of fatty infiltration on CT and liver biopsy. Results: 1) Correlation between ALT and physical measurements: Of 26 obese children, ALT was abnormally elevated (>30 IU/L) in 17 cases (67.4%) but there was no significant correlation between ALT and physical measurements (p>0.05). 2) Correlation between degree of fatty infiltration on CT and ALT: Of 26 cases, 13 cases (50%) revealed fatty liver on CT. The degree of fatty liver on CT had significant correlation with elevation of ALT (p<0.05). 3) Correlation between the degree of fatty infiltration on liver biopsy and ALT: Liver biopsy was performed in 15 cases of which 14 cases revealed fatty liver. But one case had normal hepatic histology with severe obesity and normal ALT. Fourteen fatty liver cases on liver biopsy were classified into 3 groups by the degree of fatty infiltration and analysed with obesity index and ALT. The histologic hepatic steatosis had no significant correlation with obesity index (p>0.05), but significant correlation with ALT (p<0.05). 4) Correlation between CT and liver biopsy finding: Both CT and liver biopsy were performed in 15 cases of which 6 cases revealed normal finding on CT and 9 cases manifested fatty liver. There was significant correlation between CT and liver biopsy findings (r=0.6094). Conclusion: The results of our study suggest that abdominal CT and liver biopsy are useful and accurate methods of estimating fatty liver in the childhood obesity. But biochemical abnormalities of routine liver function tests dot not correlate well with severity of the fatty liver and liver injury.

동속압연과 이속압연이 동합금판재의 조직 및 기계적 성질에 미치는 영향

이성희,임정윤,윤대진,어광준,한승전,Lee, Seong-Hee,Lim, Jung-Youn,Yoon, Dae-Jin,Euh, Kwang-Jun,Han, Seung-Zeon 한국재료학회 2011 한국재료학회지 Vol.21 No.1

The effects of conventional rolling (CR) and differential speed rolling (DSR) on the microstructure and mechanical properties of a copper alloy sheet were investigated in detail. A copper alloy with thickness of 3 mm was rolled to a 50% reduction at ambient temperature without lubrication with a differential speed ratio of 2:1; sample was then annealed for 0.5h at various temperatures from 100 to $800^{\circ}C$. Conventional rolling, in which the rolling speed of the upper and lower rolls is identical, was performed under the same rolling conditions. The shear strain introduced by the CR showed positive values at positions on the upper roll side and negative values at positions on the lower roll side. However, the shear strain showed a zero or positive value at all positions for the samples rolled by the DSR. The microstrucure and mechanical properties of the as-rolled copper alloy did not show very significant differences between the CR and DSR for the microstructure and mechanical properties. However, those properties showed very significant differences in the case of the annealed samples. The effects of rolling method on the microstructure and mechanical properties of the as-rolled and subsequently annealed materials are discussed in terms of the shear strain.

분말피복압연법에 의해 제조된 Al 분말성형체의 반복겹침접합압연

이성희,Lee, Seong-Hee 한국분말야금학회 2005 한국분말재료학회지 (KPMI) Vol.12 No.1

An aluminum powder compact consolidated by a powder-in sheath rolling (PSR) method was severely deformed by accumulative roll-bonding (ARB) process. The ARB process was performed up to 8 cycles at ambient temperature without lubrication. Optical microscope and transmission electron microscope observations revealed that microstructure of the ARB-processed Al powder compact is inhomogeneous in the thickness direction. The ultra-fine subgrains often reported in the ARB-processed bulky materials were also developed near surface of the Al powder compacts in this study. Tensile strength of the ARB-processed Al powder compact increased at the 1st cycle, but from the 2nd cycle it rather decreased slightly.

분말시스압연법에 의한 CNT 강화 Al기 복합재료의 제조 및 평가

이성희,홍동민,Lee, Seong-Hee,Hong, Dongmin 한국분말야금학회 2014 한국분말재료학회지 (KPMI) Vol.21 No.1

A powder-in-sheath rolling method was applied to a fabrication of a carbon nano tube (CNT) reinforced aluminum composite. A STS304 tube with an outer diameter of 34 mm and a wall thickness of 2 mm was used as a sheath material. A mixture of pure aluminum powders and CNTs with the volume contents of 1, 3, 5 vol was filled in the tube by tap filling and then processed to 73.5% height reduction by a rolling mill. The relative density of the CNT/Al composite fabricated by the powder-in-sheath rolling decreased slightly with increasing of CNTs content, but exhibited high value more than 98. The grain size of the aluminum matrix was largely decreased with addition of CNTs; it decreased from $24{\mu}m$ to $0.9{\mu}m$ by the addition of only 1 volCNT. The average hardness of the composites increased by approximately 3 times with the addition of CNTs, comparing to that of unreinforced pure aluminum. It is concluded that the powder-in-sheath rolling method is an effective process for fabrication of CNT reinforced Al matrix composites.

냉간압연된 Cu-3.0Ni-0.7Si 합금의 어닐링에 따른 두께방향으로의 미세조직 및 기계적 특성 변화

이성희,한승전,Lee, Seong-Hee,Han, Seung Zeon 한국재료학회 2018 한국재료학회지 Vol.28 No.2

Effects of annealing temperature on the microstructure and mechanical properties through thickness of a cold-rolled Cu-3.0Ni-0.7Si alloy were investigated in detail. The copper alloy with thickness of 3 mm was rolled to 50 % reduction at ambient temperature without lubricant and subsequently annealed for 0.5h at $200{\sim}900^{\circ}C$. The microstructure of the copper alloy after annealing was different in thickness direction depending on an amount of the shear and compressive strain introduced by rolling; the recrystallization occurred first in surface regions shear-deformed largely. The hardness distribution of the specimens annealed at $500{\sim}700^{\circ}C$ was not uniform in thickness direction due to partial recrystallization. This ununiformity of hardness corresponded well with an amount of shear strain in thickness direction. The average hardness and ultimate tensile strength showed the maximum values of 250Hv and 450MPa in specimen annealed at $400^{\circ}C$, respectively. It is considered that the complex mode of strain introduced by rolling effected directly on the microstructure and the mechanical properties of the annealed specimens.

이속압연에 의해 가공된 Cu-Ni-Si 합금의 미세 조직 및 기계적 성질

이성희,한승전,Lee, Seong-Hee,Han, Seung Zeon 한국재료학회 2016 한국재료학회지 Vol.26 No.1

Effects of conventional rolling(CR) and differential speed rolling(DSR) on the microstructure and mechanical properties of Cu-Ni-Si alloy were investigated in detail. The copper alloy with thickness of 3 mm was rolled to 50 % reduction at ambient temperature without lubricant with a differential speed ratio of 2:1. The conventional rolling in which the rolling speed of upper and lower rolls is identical was performed under identical rolling conditions. The shear strain introduced by the CR showed positive values at positions of upper roll side and negative values at positions of lower roll side. However, it showed zero or positive values at all positions for the samples rolled by the DSR. The microstrucure and texture development of the as-rolled copper alloy did not show any significant difference between CR and DSR. The tensile strength of the DSR processed specimen was larger than that of the CR processed specimen. The effects of rolling methods on the microstructure and mechanical properties of the as-rolled copper alloy are discussed in terms of the shear strain.

ARB법에 의한 인탈산동의 결정립초미세화 및 고강도화

이성희,한승전,임차용,Lee, Seong-Hee,Han, Seung-Zeon,Lim, Cha-Yong 한국재료학회 2006 한국재료학회지 Vol.16 No.9

A deoxidized low-phosphorous (DLP) copper was processed by accumulative roll-bonding (ARB) for ultra grain refinement and high strengthening. Two copper sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked to each other, and roll-bonded by about 50% reduction rolling without lubrication at ambient temperature. The bonded sheet is then cut to the two pieces of same dimensions and the same procedure was repeated to the sheets up to eight cycles (${\varepsilon}{\sim}6.3$). TEM observation revealed that ultrafine grains were developed after the 4th cycle, and their size decreased at higher cycles. Tensile strength of the copper increased with the equivalent strain, and it reached 547 MPa which was 3 times higher than that of the initial material. It is concluded that the ARB process is an effective method for high strengthening of the DLP copper.

구리튜브를 피복재로 이용한 분말시스압연법에 의해 제조된 CNT/Al 복합재료의 미세조직 및 기계적 특성

이성희,Lee, Seong-Hee 한국분말야금학회 2014 한국분말재료학회지 (KPMI) Vol.21 No.5

A powder-in-sheath rolling (PSR) process utilizing a copper alloy tube was applied to a fabrication of a multi-walled carbon nanotube (CNT) reinforced aluminum matrix composite. A copper tube with an outer diameter of 30 mm and a wall thickness of 2 mm was used as a sheath material. A mixture of pure aluminum powders and CNTs with the volume contents of 1, 3, 5 vol% was filled in the tube by tap filling and then processed to 93.3% height reduction by a rolling mill. The relative density of the CNT/Al composite fabricated by the PSR decreased slightly with increasing of CNTs content, but showed high value more than 98%. The average hardness of the 5%CNT/Al composite increased more than 3 times, compared to that of unreinforced pure Al powder compaction. The hardness of the CNT/Al composites was some higher than that of the composites fabricated by PSR using SUS304 tube. Therefore, it is concluded that the type of tube affects largely on the mechanical properties of the CNT/Al composites in the PSR process.

ARB가공된 인탈산동의 어닐링에 따른 미세조직 및 기계적 특성 변화

이성희,김춘수,김상식,한승전,임차용,Lee, Seong-Hee,Kim, Chun-Su,Kim, Sang-Shik,Han, Seung-Zeon,Lim, Cha-Yong 한국재료학회 2007 한국재료학회지 Vol.17 No.7

A deoxidized low-phosphorous copper processed by eight cycles of accumulative roll-bonding (ARB) was annealed at various temperatures ranging from 100 to $400^{\circ}C$. The annealed copper was characterized by transmission electron microscopy (TEM) and tensile & hardness test. TEM observation revealed that the ultrafine grains developed by the ARB still remained up to $350^{\circ}C$, however above $400^{\circ}C$ they were replaced by equiaxed and coarse grains due to an occurrence of the static recrystallization. The hardness of the copper decreased slightly with the annealing temperature up to $350^{\circ}C$, however they dropped largely above $400^{\circ}C$. Annealing characteristics of the copper were compared with those of an oxygen free copper processed by ARB and subsequently annealed.

6층겹침ARB공정에 의해 강소성가공된 극저탄소IF강의 어닐링에 따른 미세조직 변화

이성희,Lee, Seong-Hee 한국재료학회 2012 한국재료학회지 Vol.22 No.8

A sample of ultra low carbon IF steel was processed by six-layer stack accumulative roll-bonding (ARB) and annealed. The ARB was conducted at ambient temperature after deforming the as-received material to a thickness of 0.5 mm by 50% cold rolling. The ARB was performed for a six-layer stacked, i.e. a 3 mm thick sheet, up to 3 cycles (an equivalent strain of ~7.0). In each ARB cycle, the stacked sheets were, first, deformed to 1.5 mm thickness by 50% rolling and then reduced to 0.5 mm thickness, as the starting thickness, by multi-pass rolling without lubrication. The specimen after 3 cycles was then annealed for 0.5 h at various temperatures ranging from 673 to 973 K. The microstructural evolution with the annealing temperature for the 3-cycle ARB processed IF steel was investigated in detail by transmission electron microscopy observation. The ARB processed IF steel exhibited mainly a dislocation cell lamella structure with relatively high dislocation density in which the subgrains were partially observed. The selected area diffraction (SAD) patterns suggested that the misorientation between neighboring cells or subgrains was very small. The thickness of the grains increased in a gradual way up to 873 K, but above 898 K it increased drastically. As a result, the grains came to have an equiaxed morphology at 898 K, in which the width and the thickness of the grains were almost identical. The grain growth occurred actively at temperatures above 923 K.