http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
거형라아멘해법에 대한 고찰 - Kani-method, 소각법 및 2 cycle-method에 의한 계산결과치의 상호비교
이경기 대한건축학회 1967 建築 Vol.11 No.2
거형rahmen 에 대하여는 정산법이나 약산법을 불구하고 지금까지 여러 선현들의 많은 연구 결과로 여러가지 방법에 의하여 해결되고 있다. 현재 우리나라에는 구조계산에 대한 상세한 지침이 없어 구조계산자 자신이 습득한 가장 편리한 방법을 사용하여 문제를 해결하고 있다고 생각 한다. rahmen 의 정산법으로는 상당히 복잡한 것이 있어 간략법의 하나인 2 cycle-method를 많이 이용하는 경우가 있으나 이것은 전시중 미국에서 발전시켜 span 강비 하중항이 상위하는 rahmen에 손 쉽게 이용할 수 있다고는 하나 정산법과의 오차가 어느 정도인가 생각하여 볼만한 것이다. 정산법에 있어서도 종래에는 소각법이나 고정법을 많이 사용하였으나 근래에 와서는 비교적 계산을 간단하게 할 수 있는 kani-method 가 소개되어 이용하게 되었음을 다행하게 생각한다. 여기서는 종래 많이 사용하였던 소각법과 현재 소개되어 이용되고 있는 kani 법의 기계적 해법에 의한 결과치와 간이법의 하나인 2 cycle-method 에 의한 결과치를 산출 비교하므로서 독자들의 참고가 되도록 하겠다. 물론 계산은 실용적으로 많이 이용되는 계산척을 사용하였음을 부기하여 둔다.
李炅基 서울産業大學校 1984 논문집 Vol.20 No.1
The section of girder is deformed with the haunch existing at the ends of girder. Also, the allowable bending moment and shearing force of member will be increased by the haunch. The paper indicate the relation between the haunch size and the K-value of stiffness of girder. The increasing rate of K-value of end stiffness of girder raised to the ratio of 1.33 to 3.38, when the haunch size of ends of girder is taken as 0.1 to 0.5 times of center depth of girder.
軸荷重을 받는 콘크리트 띠鐵筋短柱의 彈性强度와 極限强度에 對한 硏究
李炅基 서울産業大學校 1980 논문집 Vol.13 No.1
The supporting floor areas which baring central axial load under the conditions of various purposes of rooms were compared, as the section areas of concretes and main steel bars were varied, with each other expressions both of the hooped short column working stress design in the Reinforced Concrete Standard of Structure Design edited by the Architectural Institute of Korea and of the strengthens among the hooped short column strengthens of the ultimate strength design in the Reinforced Concrete Design by Phil M.Ferguson According to this study, it was found that the result calculated by of the ultimate strength design had benefit of about 1.6 to 1.7 times of that by the working stress design.
李炅基 서울産業大學校 1986 논문집 Vol.23 No.1
Approximation formula of allowable bending stress ?? was derived from exact formula ?? for H-shaped section. Accuracy (=Approximation/exact value ) was ranged 1-1.11 for the case of bending moment correction factor 1, 0, 1.5, 2.3 and Fy=2.4 t/㎠, 2.8t/㎠, 3.6t/㎠. The approximation formula can be verified for more sections, but considering safety factor and the precision of results, the approximation formula can be applied for all shapes and materials without structural difficulty.
L形鋼을 事用한 組立部材의 許容휨應力度의 略算式에 對한 硏究
李炅基 서울産業大學校 1987 논문집 Vol.26 No.1
Approximation formula of allowable bending stress ?? was derived from exact formula ??for built-up section of 4 angles and a web plate. Accuracy (=Approximation/Exact value) was ranged 1-0.98 for bending moment correction factor 1.0,1.5,2.3 and Fy-2.4t/cm²,2.8t/cm² The approximation formula can be verified for more sections and materials, but considering safty factor and the precision of results, the approximation for mula can be applied without structural difficulty.
中間스티프너만 설치할 때 보에 대한 웨브플레이트의 許容座屈應力度에 關한 硏究
李炅基 서울산업대학교 1997 논문집 Vol.10 No.1
It must be confined by the bucking test that the force and the compressing force is safe, on the case of off limit in the width-thickness ratio of the web plate. When the middle stiffners are only constructioned. I suggest that we can select the simple values of the working buckling stress under permanent loads in the compressing plate σ? and shearing plate; τ? from expression.