http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
- 中文 을 입력하시려면 zhongwen을 입력하시고 space를누르시면됩니다.
- 北京 을 입력하시려면 beijing을 입력하시고 space를 누르시면 됩니다.
RISS 인기검색어
- 검색키워드
- 저자 : 심성훈 (검색결과 238 건)
- 무료
- 기관 내 무료
- 유료
-
SiC 필라멘트를 이용한 소염 직전의 확산화염 온도 계측
심성훈,신현동,Shim, Sung-Hoon,Shin, Hyun-Dong 대한기계학회 2002 大韓機械學會論文集B Vol.26 No.11
The thin SiC filament technique has been employed to identify the possibility of measuring flame temperature, and especially unstable near-extinction flame temperature in an oxidizer deficient ambience, by comparing the relative visible (non-IR) luminosities of SiC filaments with thermocouple measured temperature in co-flowing, laminar propane/air diffusion flames. The results show good agreement between the digitized relative visible luminosity profiles of the SiC filaments and temperature profiles measured using a thermocouple at temperatures above $700^{\circ}C$, although, a non-linear calibration is probably required far the whole temperature range. The highest radial peak temperature exists near to the nozzle exit. and the centerline temperatures were virtually unchanged with increasing flame height in an oxidizer deficient near-extinction flame.
-
집중 소자를 이용한 이중 대역 GSM/DCS용 적층형 다이플렉서의 설계 및 제작
심성훈,강종윤,최지원,윤영중,김현재,윤석진 한국세라믹학회 2003 한국세라믹학회지 Vol.40 No.11
본 논문에서는 고품질 적층형 수동 소자의 모델링 및 설계에 관하여 연구하였고, 설계된 수동 소자를 이용하여 안테나 스위치 모듈 내에 포함된 이중 대역 GSM/DCS 대역 분리용 적층형 다이플렉서를 설계$.$제작하여 그 특성을 고찰하였다. 적층형 수동 소자는 시스템의 소형화를 위해 인덕터는 정방형 스파이럴 구조로, 캐패시터는 입체적인 인터디지털 형태인 VIC 구조로 설계하였다. GSM 저역 통과 필터는 0.55 dB 이하의 삽입 손실과 12dB 이상의 반사 손실을 나타내며, 통과 대역 위쪽 저지 대역인 1800 MHz 부근에 감쇠극이 존재하도록 설계함으로써 DCS 통과 대역에서 26 dB 이상의 저지 특성을 나타내었다. DCS 고역 통과 필터는 0.82 dB 이하의 삽입 손실과 11 dB 이상의 반사손실을 가지며, 통과 대역 아래 쪽 저지 대역인 930 MHz 부근에 감쇠극이 존재하도록 설계함으로써 GSM 통과 대역에서 38 dB 이상의 저지 특성을 나타내었다. In this paper, the modeling and design of high-Q multilayer passives and multilayer diplexer for GSM/DCS applications designed and fabricated using these passives have been investigated.. To miniaturize the system, configurations of inductor and capacitor have involved a square spiral structure and a vertically-interdigitated capacitor similar to 3D interdigital structure, respectively. Multilayer diplexers for GSM/DCS applications were designed and fabricated to apply high-Q multilayer passives to practical systems, which were designed by the proposed structural and equivalent circuit model. LPF for GSM band had the passband insertion loss of less than 0.55 dB, the return loss of more than 12 dB, and the isolation level of more than 26 dB by locating attenuation pole at 1800 MHz. HPF for DCS band had the passband insertion loss of less than 0.82 dB, the return loss of more than 11 dB, and the isolation level of more than 38 dB by locating attenuation pole at 930 MHz.
-
-
-
평판 경계층 확산화염에서의 국부적 가속현상에 관한 실험적 연구
심성훈,하지수,신현동 대한기계학회 1988 대한기계학회논문집 Vol.12 No.4
본 연구에서는 연료분출에 박리가 있는 경우와 없는 경우 각각에 대하여 화염 대 근처의 국부가속 현상이 박리에 의하여 어떻게 영향을 받는가를 실험적으로 규명하 고, 나아가서 종래에 행해져 왔던 관련 연구 결과를 재검토할려고 한다. The main purpose of this study is to investigate the local velocity acceleration in a boundary layer diffusion flame over a flat plate. In order to know the effect of separation on the local velocity acceleration, two typical cases, flows with and without separation, are considered. For these cases, flow visualization using paraffine smoke tracers has been made. Mean velocity and r.m.s. value of fluctuating velocity are measured by using a laser Doppler velocimeter. In addition, measurements of time-mean concentration and time-mean temperature have been made. Time-mean density profiles have been obtained from the data of concentration and temperature. The obtained results are summarized as follows : (1) In the case without separation, the local velocity acceleration is clearly observed near the visible flame zone for all flow conditions. On the while, in the case with serration, the local velocity acceleration is observed only at low free stream velocity and high fuel injection velocity. As increasing the free stream velocity or decreasing the fuel injection velocity, it is not distinctly observed in the mean velocity profile. (2) The r.m.s. value of fluctuating velocity is significantly decreased by combustion in the case with separation. But in the case without separation, the r.m.s. value is increased near the visible flame zone in comparison with cold flow. In both cases, the peak value of r.m.s. appeared just at the visible flame zone, where the mean velocity gradient is not too high.
-
-
전류예측기를 이용한 10비트 저전력 전류구동 CMOS A/D 변환기 설계
심성훈,권용복,윤광섭 대한전자공학회 1998 電子工學會論文誌, C Vol.c35 No.10
본 논문에서는 휴대용 영상신호처리 시스템에 집적화할 수 있는 전류예측기와 모듈형 기준전류원을 이용한 10비트 저전력 전류구동 CMOS A/D 변환기를 설계하였다. 전류예측기와 모듈형 기준 전류원을 사용함으로써 2단 플래시구조를 갖는 A/D 변환기에 비해 비교기와 기준전류원의 개수를 줄일 수 있게 되었고, 따라서 설계된 A/D변환기의 저전력 동작이 가능하였다. 설계된 10비트 저전력 전류구동 CMOS A/D 변환기는 0.6㎛ n-well single-poly triple metal CMOS 공정을 사용하여 제작되었다. +5V 단일 공급전압하에서 동작할 때 측정된 전력소모는 94.4mW이며, 아날로그 입력 전류범위는 16㎂에서 528㎂로 측정되었으며, INL과 DNL은 각각 ±1LSB, ±0.5LSB이하로 나타났다. 또한 10MSamples/s의 변환속도를 나타내었고, 제작된 10비트 전류구동 CMOS 4/D 변환기의 유효 칩면적은 1.8㎜ x 2.4㎜이다. In this paper, an 10 bit current-mode CMOS A/D converter with a current predictor is designed with a CMOS process to be integrated into a portable image signal processing system. A current predictor let the number of comparator reduce to 70 percent compared with the two step flash architecture. The current magnitude of current reference is reduced to 68 percent with a modular current reference. The designed 10 bit Low-power current-mode CMOS A/D converter with a current predictor is simulated with HSPICE using 0.6$\mu\textrm{m}$ N-well single-poly triple-metal CMOS process parameters. It results in a conversion rate of 10MSamples/s. A power consumption is measured to be 94.4mW at single +5V supply voltage. The 10 bit A/D converter fabricated using the same process occupies the chip area of 1.8mm x 2.4mm.
-
-
-
알칼리 금속계 전처리탈황제의 미분탄연소 배연탈황 적용성 연구
심성훈,이철,노창래,최홍기,한신,김두진 한국열환경공학회 2022 열환경공학 Vol.17 No.1
An experiment was conducted to reduce sulfur oxides by burning low-calorie, low-sulfur sub-bituminous coal treated with an alkali metal-based coal pretreatment desulfurization agent. As a result of pre-combustion treatment with 0.3% desulfurization agent, it was possible to reduce sulfur dioxide by 96.83ppm from 97.10ppm to 0.27ppm on average compared to raw coal at 6% reference oxygen concentration, and the maximum reduction rate was found to be 99.70% on average. Additional research is needed on whether such a reduction rate is possible even in the case of high-sulfur coal treatment, but by using an alkali metal-based pre-combustion desulfurization agent, the emission of sulfur dioxide could be dramatically reduced for low-sulfur sub-bituminous coal. In the future, it will be possible to minimize the emission of sulfur dioxide to the atmosphere by operating in combination with FGD, which is a post-treatment facility.
연관 검색어 추천
이 검색어로 많이 본 자료
활용도 높은 자료
