http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
LRFD에 의한 연속보 주부재의 조밀 및 비조밀 단면 최적화 설계
국중식,신영석,Gook, Joong-Sik,Shin, Yung-Seok 한국강구조학회 2000 韓國鋼構造學會 論文集 Vol.12 No.3
하중-저항계수 설계법(LFRD)에 따르면, 단면 형상은 압축 요소의 폭-두께비 및 브레이스 조건에 따라 조밀, 비조밀, slender로 나누어 설계가 되어지고 있다. 본 논문에서는 LRFD시방서의 내용을 기준으로 2경간 연속보의 주형인 I형 거더를 조밀단면과 비조밀단면으로 나누어 설계하였으며, 최적화 기법을 도입하여 단면을 설계하였다. 본 연구는 최적화 기법을 이용하여 조밀 및 비조밀 단면에서의 단면 형상의 변화를 고찰하였다. The Load and Resistance Factor Design(LRFD) Specification defines two sets of limiting width-to-thickness ratios. On the basis of these limiting values, steel sections are subdivided into three categories: compact, noncompact, and slender sections. In this paper, I-Type girders of a 2 span continuous steel bridge are divided into compact and non-compact sections and analyzed. In the design process, an optimization formulation was adopted and ADS, a Fortran program for Automated Design Synthesis, was used. In this study, we studied about change of the section between compact and non-compact using optimization formulation.
안모의 수직적 양태에 따른 골격 및 치조골의 위치 관계에 관한 연구
오중식,국윤아,김상철 대한치과교정학회 1999 대한치과교정학회지 Vol.29 No.3
교정 증례의 분석 예후 추정은 두개골의 수평 및 수직적인 관계가 동시에 고려되는 입체적 관점에서 평가되어야 한다. 따라서 본 연구에서는 성장이 완료된 성인 남녀 각 100명을 추출하여 두부 방사선 사진을 채득한 후 하안면 고경과 상안면 고경의 비율로 안모의 수직적 수직적 형태를 구분하여 군을 설정하였으며 이들 군간의 골격 및 치조골의 크기와 위치 관계를 비교하고 상호 관련성을 조사하여 다음과 같은 결과를 얻었다. 1. 치조고경, 안면 고경, lower gonial angle, 그리고 FMA 항목에서 하안면 고경이 큰 군의 것이 작은 군에 비하여 유의하게 크게 나타났다. 2. 치조고경, 안면고경, 하악지 고경, 그리고 Jarabak ratio 항목에서 남서이 여성에 비하여 유의하게 크게 나타났다. 3. 치성 및 골격성의 수직계측항목과 UAFH/LAFH의 상관관계 조사에서 치조고경,안면고경, lower gonial angle, FMA 그리고 Bjok's Sum 항목이 UAFH/LAFH와 유의한 상관관계를 보였다. The purpose of this study was to investigate the variations of the skeletal and dentoalveolar dimensions in relation to vertical facial patterns. Lateral cephalogram of 200 cases (100 cases of male and 100 cases of female, average age of which was 23.2 years) were traced and some measurements of skeletal and dentoalveolar dimensions were measured. The ratio of UAFH/LAFH was employed to classify the samples into groups of excess and short lower anterior facial height. And the comparison between two groups were taken statistacally. The following results were obtained. 1. The dentoalveolar height, lower anterior facial height, lower gonial angle, and FMA in the excess-lower-anterior-facial-height group were significantly larger than those in short-lower-anterior-facial-height group. 2. The dentoalveolar height, ramus height, and Jarabak ratio in the male subjects were significantly larger than those in the female subjects. 3. The UAFH/LAFH ratio showed a significant correlation to upper, lower facial height, AUDH, PUDH, ALDH, PLDH, Lower gonial angle, FMA, and Bjork's Sum.
안모의 수직적 양태에 따른 골격 및 치조골의 크기에 관한 연구
오중식,김상철,국윤아 원광대학교 치의학연구소 1997 圓光齒醫學 Vol.7 No.1
The purpose of this study was to investigate the variations of the skeletal and dentoalveolar dimensions in relation to vertical facial patterns. Lateral cephalogram of 200 cases (100 cases of male and 100 cases of female, average age of which was 23.2 years) were traced and some measurements of skeletal and dentoalveolar dimensions were measured. The ratio of UAFH/LAFH was employed to classify the samples into groups of excess and short lower anterior facial height. And the comparison between two groups were taken statistacally. The following results were obtained 1. The dentoalveolar height, lower anterior facial height, lower gonial angle, and FMA in the excess-lower-anterior-facial-height group were significantly larger than those in short-lower-anterior-facialheight group. 2. The dentoalveolar height, facial height, ramts height, and Jarabak ratio in the male subjects were significantly larger than those in the female subjects. 3. The UAFH/LAFH ratio showed a significant correlation to upper, lower facial height, AUDH, PUDH, ALDH, PLDH, Lower gonial angle, FMA, and Bjark' s Sum.