http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
한문식,박태인,Han, Mun-Sik,Park, Tae-In 한국기계연구원 1985 기계연구원소보 Vol.15 No.-
In this paper, temperature distribution and thermal stress are investigated considering engine peak pressure and the time average temperature distribution in the piston under running conditions for the diesel engine. The induced stress are calculated by the Finite Element Method(FEM). The results obtained are summerized as follows. 1) The results calculated by the FEM present good agreement with other numerical solution in literature. 2) It is confirmed that maximum compressive stress are induced in the part of outside wall between the piston crown and the pin bush. 3) In the axial direction, the hoop stresses are changed its sigh at the portion of crown near the inner wall side 4)Large gradient of temperature is shown in the piston crown near the side wall in the axial direction, in the part between the piton crown and the pin bush in radical direction 5)in case of stress distribution of piston wall surface in the axial direction, the hoop stress is a little greater than axial stress, and the latter is greater than the radial stress
박용 구조물용 일반압연강 용접부의 피로균열 전파거동에 미치는 $K_{II}$의 영향
한문식,김상철 대한용접접합학회 1988 대한용접·접합학회지 Vol.6 No.3
An experimental study was carried out to identify the fatigue fractue behavior of weld zone in generally rolled steel for marine structure. The bending an shear loads were applied simultaneously on the specimens to simulate real load condition for marine structure. The effect of the stress intensity factor under mode I with II loading condition on the initiation and the propagation of a crack were investigated, with particular emphaiss on mode II. When the $K_{II}$ stress intensiy factor in mode II was applied under mode I load condition, the growth behavior of a crack seems to be affected mainly by the anisotropic characteristic of materials. Especially, when the crack was located in and near the weld zone and parallel to th weld line, the propagation behaviour was turned out to be quite different from that of the base metal along the direction transverse to the weld line. In general, the propagation veiocity of the cracks in and near the weld zone was found to be slower that the velocity in base metal.
한문식,조재웅 한국기계가공학회 2015 한국기계가공학회지 Vol.14 No.3
As riders do not sense damage to hub bearings due to the friction that occurs while riding, unexpected accidents can happen. Hub bearings can also be broken by cracks due to minor impact. Therefore, the vibration analysis of bike hub bearings is thought to be important. Two bike hub bearings were modelled in this study. The bolts at both ends of the bearings were fixed. The standard weight of a Korean man was assumed to be 70Kg, and a force of 700N was applied. As a result of this study, maximum deformations occurred in bolts at both ends of the central axis. Regarding displacement due to natural frequencies, Model 2 had less deformation than Model 1. Using the results of this study, the structural safety of the design of hub bearings can be estimated, and design plans for durable hub bearings can be suggested.
한문식,조재웅 한국기계가공학회 2015 한국기계가공학회지 Vol.14 No.2
This study investigated the durability of the under bar of a car through structural and fatigue analysis. Model 1 had the lowest value among three kinds of models. In the case of the maximum equivalent stress and displacement at structural analysis, model 1 showed the highest durability. Also, models 3 and 2 showed structural durability in order of this value. In the case of fatigue analysis, the maximum fatigue lives of the three models were equal to 2×107cycles. However, model 1 showed the highest value among the three models, as the minimum fatigue life of model 1 becames 92.56 cycles. Also models 3 and 2 showed fatigue durability in order of this value. The maximum possibility of fatigue damage for models1,2,and 3 became 30%. If the results of this study are applied to change the design shape of the under bar of cars, the ride comfort for automobile passengers and car durability can be improved.