http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
- 中文 을 입력하시려면 zhongwen을 입력하시고 space를누르시면됩니다.
- 北京 을 입력하시려면 beijing을 입력하시고 space를 누르시면 됩니다.
RISS 인기검색어
- 검색키워드
- 저자 : 김광수(Gwang Soo Kim) (검색결과 80 건)
- 무료
- 기관 내 무료
- 유료
-
TFT-LCD 백라이트 유닛(BLU) 램프용 전극 미세 접합부의 강도 및 미세조직
김광수,김상덕,Kim, Gwang-Soo,Kim, Sang-Duck 한국재료학회 2009 한국재료학회지 Vol.19 No.1
TFT-LCD is the most popular type of flat display panel in the information technology field. The back light unit is a main part of the structure of a TFT-LCD panel. Occasionally, studies have shown that failures of the CCFL of the BLU occur due to the poor weld characteristics of these materials. The aim of this study was to prepare some technical data and to characterize a microjoined electrode for the CCFL. Microstructure examinations, microhardness measurements, resistance measurements and microtensile tests of the microjoined electrode were carried out. The result indicates that a large amount of grain coarsening exists in the heat-affected zone (HAZ) of the weld between the cup and the pin. This grain coarsening of the HAZ between the cup and pin is caused by the welding cycle, which may have an influence on the lowest microhardness values. Fracturing of the microjoined electrode also occurred at the HAZ close to the cup between the weld holding the cup and the pin. Additionally, no specific changes of the electrical resistance among the cup, pin, and lead wire themselves or in the microjoined electrode were observed.
-
페로 소재로 만들어진 고크롬계 내마모재의 미세조직과 경도
김광수,Kim, Gwang-Soo 한국재료학회 2006 한국재료학회지 Vol.16 No.1
This study was performed to investigate the characteristics of the synthesized powder type ferro materials for wear resistant hardfacing. The powder type filler materials were made from ferro Cr and ferro Mn. Those ferro materials are two types, such as high carbon and low carbon contained. The alloy composed of high carbon ferro Cr and high carbon ferro Mn exhibited the best properties in terms of microstructure and hardeness for wear characteristics. Further, the alloys produced by the synthesized powders and wire type filler, were also evaluated in terms of microstructures and microhardness measurements. The results indicated that the synthesized powders displayed reasonable properties compared to commercial grade materials. The hardness value of the alloy produced by the synthesized powders were approached about 90% of the commercial grade's hardness. The hardness values of the alloys closely depended on the amount of the dissolution of the ferro Cr, the hardness and the volume of the eutectic phase.
-
치과 치료학에서 적용되는 접합기술 연구 ; 스테인리스강 크라운에 접합된 직접용 콤포짓트 레진과 간접용 콤포짓트 레진의 전단결합강도 비교
김광수,백광우,Kim, Gwang-Soo,Baek, Kwang-Woo 대한용접접합학회 2011 대한용접·접합학회지 Vol.29 No.4
This study was performed to compare the shear strength of the bondings between stainless steel crown/direct type composite resin and stainless steel crown/indirect type composite resin. Four groups of bonding conditions were prepared. Two groups of bonding conditions were made by the indirect type composite resin system and the other two groups were made by the direct type composite resin system. The shear strength tests were carried out using universal testing machine, Model 4465 of Instron Co.. It was indicated that the bond strength values of the indirect type composite resins were higher than those of the direct type composite resins. TE-SE group was superior to the TE-ONE in indirect type resin system. These results were thought to be the high degree of the polymerization accompanied with temperature and pressure of the resin of indirect type resin. It was also found that indirect composite resin contains less amount of porosity in resin.
-
미세 용접된 BLU CCFL 전극의 유리비딩 열처리 온도에 따른 접합부 특성
김광수,김상덕,권혁동,Kim, Gwang-Soo,Kim, Sang-Duck,Kwon, Hyuk-Dong 대한용접접합학회 2009 대한용접·접합학회지 Vol.27 No.4
Characterization of the microweld CCFL electrode for the TFT-LCD backlight unit was carried out in terms of the glass beading heat treatment conditions. We evaluate the weld zone and parent metal of the microweld CCFL electrodes that were exposed to simulated glass beading heat treatment. The CCFL electrode was composed of the cup made with pure Ni, the pin made with pure Mo and the lead wire made with Ni-Mn alloy. Each part of the electrode was assembled together by micro spot welding process and then the assembled electrodes were exposed to simulated glass beading temperatures of $700^{\circ}C,\;750^{\circ}C$ and $800^{\circ}C$. The microstructures of the microweld CCFL electrode were observed by using optical microscope, scanning electron microscope and EDS. Micro-tensile and microhardness test were also carried out. The results indicated that the grain coarsening in the HAZs(heat affected zones) for both the cup-pin weld and pin-lead wire were exhibited and the grain coarsening of the HAZ for the cup and the lead wire was more obvious than the HAZ of the pin. The micro-tensile test revealed that the fracture occurred at the cup-pin weld zone for all test conditions. The fracture surface could be classified into two parts such as pin portion and cup portion including weld nugget. The failure was seemed to be initiated from the boundary between nugget and pin through the weld joint. The result of the microhardness measurement exhibited that the relatively low hardness value, about 105HV was recorded at the HAZ of the cup. This value was about 50% less than that of the original value of the cup. The reduction of the microhardness was considered as the cause of the grain coarsening due to welding process. It was also appeared that there was no change in electric resistance for the standard electrodes and heat treated electrodes.
-
-
김광수(Kim, Gwang-Soo),김상덕(Kim, Sang-Duck) 한국산학기술학회 2008 한국산학기술학회논문지 Vol.9 No.2
Ag계 분말 삽입금속을 볼 밀링법으로 제조하였다. 밀링공정의 변수들은 밀링시간을 제외하고는 일정하게 하였고 밀링 시간은 24, 48, 72시간들로 정하였다. 밀링에 의해 제조된 삽입금속들은 SEM관찰, DSC분석, 퍼짐성, 젖음성 시험을 통해 평가하였다. 삽입금속들의 브레이징부 특성은 상용금속에 비하여 우수하였다. 48시간 동안 밀링한 삽입금속이 퍼짐성과 젖음 특성이 가장 우수한 조건임을 나타냈다. 또한 브레이징부는 작은 양의 기공을 포함하고 있지만 안정적인 미세조직을 보였고 미세경도는 138VHN으로 나타났다. Powder type Ag system insert metals were manufactured by ball milling process. The variables of milling process were constant except the milling time. The milling times were selected for 24, 48 and 72 hours. The insert metals made by milling process were evaluated by performing scanning electron microscope, DSC(differential scanning calorimetry) analyses, spreading test and further in terms of wettability test. The selected insert metals that have the good characteristics compared to commercial insert metals were applied to make the brazed joints. The characterizations of those brazed joints were also conducted by microstructural observations. The results indicated that milling time of 48 hours for making powder type insert metals was the best condition showing the good spreadibility, low wetting angle. The brazed joints that applied the 48 hours milled insert metal were very sound condition indicating the stable microstructure in spite of containing small amount of porosity and the microhardness value of the joint was about 138VHN.
-
인터넷 응용 서비스 제공을 위한 IPv4/IPv6의 성능 분석
김광수(Gwang-Soo Kim),김광현(Gwang-hyun Kim) 한국통신학회 2004 한국통신학회논문지 Vol.29 No.8B
현재 인터넷은 IPv6로 전환하기 위한 과도기적 단계에 있으며 IPv6 기반의 네트워크 관련 제품들이 출시되고 있다. 이렇게 장비 개발에 많은 투자가 이루어지고 있지만, 장비 개발과 함께 응용 서비스 기술의 중요성이 강조되고 있다. 이러한 응용 서비스 기술의 개발을 위해서는 다양한 응용 서비스에 대한 실험이 필요하다. 현재까지의 수된 연구는 앞으로 전개될 IPv6 망을 위해 IPv4와 IPv6에서 망들간 라우터의 성능 측정에 초점을 맞추고 있으며 인터넷 응용 서비스를 제공하기 위한 성능 측정은 아직까지 진행되지 않고 있다. 본 논문에서는 IPv6의 도입에 따라 현재 구축되어 있는 네트워크 인프리와 프로토콜에 관계없이 인터넷 응용 서비스가 성능이 저하되지 않고 사용될 수 있는지에 대한 성능 분석을 하였다. 본 논문의 실험 결과 각 망들에서 종단간 인터넷 응용 서비스의 성능은 Native 망에 비해 Dual 망의 효율이 떨어짐을 알 수 있었다.
-
-
-
ScienceON
코리아스칼라연관 검색어 추천
이 검색어로 많이 본 자료
활용도 높은 자료
