Misorientation Characteristics at the Growth Front of Abnormally-Growing Goss Grains in Fe–3%Si Steel

Tae‑Young Kim,Tae‑Wook Na,Hyung‑Seok Shim,Yong‑Keun Ahn,Yong‑Kwon Jeong,Heung Nam Han,Nong‑Moon Hwang 대한금속·재료학회 2021 METALS AND MATERIALS International Vol.27 No.12

Penetrating morphologies at the growth front of abnormally-growing Goss grains in Fe–3%Si steel was examined in view ofthe possibility that they are the two-dimensional section of the solid-state wetting (SSW) along the triple junction line. Toobtain the statistically meaningful data, 102 penetrated grain and 204 penetrating abnormally-growing Goss grain morphologieswere examined. The misorientation angles of penetrating and penetrated grains were measured by electron backscattereddiffraction. Among the 102 examined penetrated grain boundaries, none has low misorientation angles less than 15°,whereas 17.2% of the 204 penetrating grain boundaries have low misorientation angles, and 23.5% of them have coincidencesite lattice boundaries. Besides, boundary energies of penetrating Goss grains, which were estimated from misorientationangles of the three grains in the penetrating morphology, satisfied the energetic condition for SSW along the triple junctionline. These results imply that the abnormal grain growth of Goss grains in Fe–3%Si steel occurs by the mechanism of subboundaryenhanced SSW.

低速 高토크形 空氣壓 베인 모터 開發

황광성,김명규,정태상 진주산업대학교 산업과학기술연구소 2007 산업과학기술연구소보 Vol.- No.14

Air pressure Vane motor applied in this paper can be used very widely. Motor developed in domestic has about 80% efficiency of income product. Therefore, torque is increased because improve small size(1200rpm) Low-speed High torque type Air pressure Vane motor's quality of the material and special quality and do so that decelerate output and conclusion that consider and manufacture number of rotations and efficiency etc. Obtained results are summarized as follows: 1. Dust and corrosion can be reduced and 20% bulk of casing housing decreased by optimizing of alternated casing site. 2. Vane's wing optimum number is composed of 5 by Vane type wing and Gear Ratio's design choice and torque raised by eccentricity 28mm of rotor and cylinder and reduction of rpm (gear ratio 1/2.6). 3. Air pressure Vane motor's research and development connected with various output is judged that it is serious as for counter measure late.

배기가스 재순환에 의한 실린더 및 피스톤 마모에 미치는 영향에 관한 연구

황광성,김태규,정태상,김유영,하정호 진주산업대학교 산업과학기술연구소 2003 산업과학기술연구소보 Vol.- No.10

The effects of recirculated exhaust gas on the wear of cylinder liner, piston and piston rings have been investigated by the experiment with a two-cylinder, four cycle, indirect injection disel engine operating at 75% load and 1600 rpm spped. For the purpose of comparison between the wear rates of two cylinders with and without EGR, the recirculated exhaust gas is sucked into one of two cylinders after the soot among exhaust emissions is removed by an intentionally designed cylinder-type scrubber equipped with 6 water injectors(A water injector has 144 nozzles of 1.0 mm diameter), while only the fresh air into another cylinder. These experiments are carried out on the fuel injection at a fixed 15.3˚BTDC timing. It is found that firstly the mean wear amount of cylinder liner with EGR is more increased in the measurement positions of the second half than of the first and the mean wear amoount without EGR is almost uniform regardless of measurement positions, secondly the wear rates of the first and second piston ring(compression ring) thickness with EGR are more than twice, but the wear rate of oil ring thickness without EGR is more increased than that with EGR, and finally the wear rate of piston skirt with EGR is a little bit increased, but the piston head diameter is rather increased owing to soot adhesion and corrosion wear, and especially larger with EGR.

전기장이 걸린 양자우물 구조의 바닥상태 특성

황형준,권태진,최정우 慶熙大學校 材料科學技術硏究所 1999 材料科學技術硏究論集 Vol.12 No.-

We estimate the ground state energy and wavefunction in the biased quantum well structure by using the periodic boundary condition. In this calculation, we assumed that the probability of finding the particle has maximum value at the ground state energy and the amplitude of the wavefunction should not depend on a period. The obtained energy value was in good agreement with the result predicted by the complex energy method.

결핵균체 추출액으로부터 알파 및 베타단백항원의 정제에 관한 연구

황인택,백태현,김화중,박정규,최대경 충남대학교 의과대학 지역사회의학연구소 1990 충남의대잡지 Vol.17 No.1

It is well known that α- and β-antigens are major protein products of Mycobacterium tuberculosis. Alpha and beta antigens from the cell extract of Mycobacterium tuberculosis were purified by 80% ammonium sulfate precipitation, gel filtration of Sephacryl S-300, DEAE-Sephacel ion exchange chromatography and hydroxylapatite chromatography. Beta antigen was purified further by column preparative polyacrylamide gel electrophoresis. The purified alpha and beta antigens were checked degree of purified by SDS-polyacrylamide gel electrophoresis. The results were summarized as follows: 1. Alpha antigen was purified by ammonium sulfate precipitation, gel filtration, ion exchange chromatography and hydroxylapatite chromatography. The purified alpha antigen showed a distinct band of 30 KDa molecule on SDS-polyacrylamide gel electrophresis. 2. Beta antigen was purified by ammonium sulfate precipitation, gel filtration, ion-exchange chromatography, hydroxylapatite chromatography and column preparative polyacrylamide gel electophoresis. The purified beta antigen showed two distinct bands of 83 KDa and 52 KDa molecules on SDS-PAGE. 3. Especially, Beta antigen was absorbed well to hydroxylapatite column but alpha antigen was passed completely without absorption.

포괄수가지불제도 적용에 따른 산부인과 진료수입의 변화

황태연,유병철,정귀언,정수진,김성준,배기택,손혜숙,이종태,전진호,엄상화 인제대학교 2001 仁濟醫學 Vol.22 No.1

Objectives: Under the fee-for-service system, Korean hospitals have been suffering from the worsening profitability caused by law medical care fees. To overcome the difficulties, they have maximized the quantity of medical services and made relatively large investment in developing new medical services using high-priced medical equipment, medicines and medical supplies which were not covered by medical insurance system rather than reduced running costs. Materials and Methods: This study was made to analyze and forecast the revenue change of the department of Obstetrics and gynecology of an university hospital in Seoul, expecting the implementation of DRG system in 2000. Results: The results were as follows : 1.During the first two days of hospitalization. 41% of total medical service fee was occurred, which was thought that most of the check-ups and operations were made during this period. After two days of hospitalization, the new occurrence of medical service fee tended to reduce. 2.Out of total medical service fee, 67% of admission fee was occurred after 5 days of hospitalization. This was because medical service fees in obstetrics and gynecology department occurred during the first 5 days of hospitalization. 3.Out of fees for operation, treatment, medical supplies and blood transfusion. 71% was occurred during the first two days. 4. In case of fees for examination, 50% was occurred during the first two days. 5.A total of 53% of fees for medication and injection was occurred during the first 5 days. Conclusions: By the implementation of the DRG system, the income is forecast to increase by 800 won to 310,000 won by the disease group of obstetrics and gynecology department. To increase hospital income with the implementation of DRG system, the results of this study suggest that examinations should be done at out-patient departments before the hospitalization of patient, the discharge of patient should be noticed in advance to reduce the period of hospitalization, and admission appointment system should be implemented for the immediate operation and delivery.

SM20C 旋削時 加工條件 變化에 따른 칩 形狀에 관한 硏究

정태상,황광성,김명규,김길진,박영태 진주산업대학교 산업과학기술연구소 2007 산업과학기술연구소보 Vol.- No.14

This study was to look for cutting conditions which are safe, comfortable and contributable to the increase in productivity at the time in turning. The shape of chips while turning have a strong effect on cutting processing. If chips fail to be well controlled, systematic cutting is not possible by revolution of chips entangled with workpiece or damage of tool edges, and this causes problems threatening the safety of the operator. This study is designed to identify conditions which chips effectively controlled and able to treat properly, and the results are as follows: 1. Feed rate, which determined the shape of chips, was found to have a stronger impact on the shape of resulting chips than any other cutting condition. 2. When feed rate was 0.25mm or over, controlled chips(coil spring type) were produced under whatever cutting conditions. 3. When feed rate was 0.25mm or over and depth of cut was 1.0mm, well-controlled shorter coil type chips were produced at every spindle speed, which implied they were the most suitable cutting conditions. 4. Feed rate 0.2mm was found to be an unstable section where coil spring and linear mixed type chips were produced together, and as feed rate decreased, more linear chips beyond control were produced. 5. At the same spindle speed, as the diameter of the material became bigger, controlled chips were produced only when the depth of cut was reduced, and vice versa under feed rate 0.2mm. 6. At the same feed rate, the lower spindle speed was, the more stable chips were produced.

평양 남정리 53호분 출토 토제칠기의 보존 및 제작기법 연구 : 토제칠이배, 토제칠반, 토제칠안

황현성,임수경,김희진,이태진,고민정,윤은영 국립중앙박물관 2013 고고학지 Vol.19 No.-

본고는 일제 강점기 조사 미등록 유물 정리사업의 일환으로 수행한 평양 남정리 53호분 출토 토제칠이배, 토제칠반, 토제칠안에 관한 연구이다. 남정리 출토 유물은 소지가 목심이 아닌 토제라는 것과 칠이배와 칠반을 얹은 칠안이 함께 출토되었다는 점에서 주목할 만하다. 토제칠이배 및 칠반 그리고 칠안의 보존처리를 통해 이들의 형태와 문양 등에 대해 알 수 있었다. 또한 칠기에 사용된 붉은색 안료의 성분을 분석하여 안료의 주성분이 진사(HgS)였음을 확인하였다. 이번 연구에서 기존에 잘 알려지지 않았던 한반도 내 위치한 낙랑의 토제칠기에 관해 살펴볼 수 있었으며 이러한 제작방법이 한나라 고유의 문화인지 아니면 재지세력이 한나라의 영향을 받아 현지화한 문화의 산물인지에 대해 생각해 볼 수 있는 기회라 생각된다. This research paper examines the lacquered pottery cup, plate and table unearthed from Tomb No. 53 at Namjeong-ri in Pyongyang, which were under conservation treatment as a part of the Project of Unregistered Artefacts Uncovered in the Japanese Colonial Era. It is very rare to have a lacquered pottery cup and plate, lying on a lacquered pottery table, as a set of grave goods. In particular, they are not wooden but pottery items. Through conservation treatment for lacquered pottery cup, plate and table, it was possible to find out their shapes and decoration patterns. The resulting analysis of the red pigment used indicates that cinnabar (HgS) is the main element. This research is significant because it examines lacquered pottery wares produced in Lelang, which has rarely been conducted. Further research will need to prove whether their production techniques were in the unique Chinese Han style or were produced by indigenous craftsmen who adopted the Chinese Han technique.

코호넨 네트워크 및 시간 지연 신경망을 이용한 움직이는 물체의 중심점 탐지 및 동작특성 분석에 관한 연구

황정구,김종영,장태정 江原大學校 産業技術硏究所 2001 産業技術硏究 Vol.21 No.B

In this paper, center detection and motion analysis of a moving object are studied. Kohonen's self-organizing neural network models are used for the moving objects tracking and time delay neural networks are used for dynamic characteristic analysis. Instead of objects brightness, neuron projections by Kohonen Networks are used. The motion of target objects can be analyzed by using the differential neuron image between the two projections. The differential neuron image which is made by two consecutive neuron projections is used for center detection and moving objects tracking. The two differential neuron images which are made by three consecutive neuron projections are used for the moving trajectory estimation. It is possible to distinguish 8 directions of a moving trajectory with two frames and 16 directions with three frames.

전기 화상 환자의 수술 전 평가,고압손상과 저압손상 비교

황정원,이정기,전영태,강종만,오용석,노규정,김현철 대한정맥마취학회 2004 정맥마취 Vol.8 No.1