http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
단부 보강한 합성보(Eco-girder)의 이력거동에 대한 수치해석적 연구
채흥석,류재용,정경수,문영민,최성모,Chae, Heung-Suk,Ryoo, Jae-Yong,Chung, Kyung-Soo,Moon, Young-Min,Choi, Sung-Mo 한국강구조학회 2010 韓國鋼構造學會 論文集 Vol.22 No.6
The end-reinforced composite-beam (eco-girder) system was developed that has characteristics of the existing composite beams such as reduced floor height and increased strength. With it, less use of steel is expected. In the eco-girder system, only both ends of the steel-frame beam, which are vulnerable to the ultimate moment, are reinforced with steel plates so that the steel frame beam design will be based on the moment at the beam center. This study used fiber element analysis, which is a simple representation and numerical integration of the principles of the detailed Finite Element Method(FEM), to predict the hysteretic behavior of reinforced composite beams under cyclic loading. The validity of the numerical method was verified by comparing the results of this study with those of previous studies. In addition, the hysteretic behavior of the eco-girder was compared with that of the existing composite beams. 층고 감소, 내력 증대 등의 장점을 가지고 있는 기존 합성보의 특징 뿐만 아니라 사용 강재량의 감소까지 기대할 수 있는 단부 보강한 합성보(Eco-girder) 시스템이 개발되었다. Eco-girder 시스템의 개념은 효율적인 합성보의 설계를 위해 최대 모멘트가 발생하는 양단부만을 강판을 이용하여 보강하고, 중앙부 모멘트에 의하여 철골보 크기를 결정하는 구조시스템이다. 본 연구에서는 반복 휨하중을 받는 단부보강 합성보의 이력거동을 예측하기 위해 정밀한 FEM(Finite Element Method)보다는 간단한 표현과 동시에 원리에 충실한 수치적분에 의한 면내수치해석방법(Fiber Element Analysis)을 이용하였으며, 선행 연구된 실험 결과와의 비교를 통해 수치해석방법의 타당성을 검증하였다. 또한 기존 합성보와의 이력거동을 비교 분석하였다.
단부 보강한 합성보(에코거더)시스템의 구조성능에 관한 실험적 연구
채흥석,류재용,정경수,문영민,최성모,Chae, Heung-Suk,Ryoo, Jae-Yong,Chung, Kyung-Soo,Moon, Young-Min,Choi, Sung-Mo 한국강구조학회 2010 韓國鋼構造學會 論文集 Vol.22 No.6
H형강 보는 기둥 사이에 설치되어 건물의 각 층 바닥인 슬래브를 지지하기 위해 널리 사용되고 있다. 그러나, H형강 보의 경우 접합부가 고정단이면서 등분포하중 작용시 양 단부에 발생하는 휨 모멘트는 중앙부에 발생하는 모멘트에 비해 약 2배가량 크다. 보는 최대 모멘트에 의해 설계가 이루어지기 때문에 보 춤이 커지게 되고, 이로 인하여 각 층의 가용 공간이 줄어드는 문제점이 있다. 이를 개선하기 위해, 최대 휨 모멘트가 발생하는 H형강 보 양 단부만을 별도로 보강하면, 보 중앙부에서 발생하는 휨 모멘트로 보를 설계할 수 있다. 따라서, 단부 보강한 철골보(Eco-girder)의 구조적 성능을 분석하기 위해, 단부 보강 강판의 용도, 철근 보강, 하중전달방법 등을 변수로 하여 4개의 실험체를 제작하여 구조성능실험을 수행하였다. H-shaped beams, which are constructed between columns, are used widely as slaves in steel structures. The bending moments that occur on both ends of an H-shaped beam, however, are about twice the bending moment that occurs at the center of the H-shaped beam. Because such beam is designed with maximum bending moment, it is deeper and has smaller spaces. To improve these features, if both ends of an H-shaped beam that have maximum bending moments are merely reinforced, the beams could be designed by the bending moment at the center of the H-shaped beam. To analyze the structural performance of the proposed end-reinforced beams (eco-girders). Four specimens were prepared with the following parameters: end-reinforced steel plate, reinforced bars, and reinforced studs and experimental tests of the specimens were performed.
SN 강재를 이용한 엔드플레이트항복형 보-기둥접합부의 구조 거동
이세정,채흥석,이성희,김진호,최성모,Lee, Se-Jung,Chae, Heung-Suk,Lee, Seong-Hui,Kim, Jin-Ho,Choi, Sung-Mo 대한건축학회 2011 대한건축학회논문집 Vol.27 No.6
In End-Plate connection, End-Plate and beam are welded in a factory and fastened with bolts in the field. End-Plate connection, one of Partial Rigid Connections(PR) has been observed the structural behavior and deformation performance equivalent to Full Rigid Connections(FR). Four impossible failure modes of End-plate connection subjected to hysteresis behavior are categorized into the plastic deformation in the End-Plate and the beam yielding, the bolt failure, the brittle failure of weld section, The beam yielding and plastic deformation in the End-Plate can perform the enough ductility behavior and inelastic deformation, while the bolt failure and brittle failure of weld section can not perform it. It is important that End-Plate connection prevents the brittle failure and procures the reliability of connection. In this paper, it is propose to occur the plastic deformation in the End-Plate and to procure the reliability of connections. Therefore, we suggested End-Plate yielding connections using only End-Plate for New Steel(SN Steel) limited between upper and lower yield point in order to obtain the enough ductility behavior and End-Plate inelastic deformation.
이숙희(Suk-Hee Lee),채흥석(Heung-Seok Chae),권용래(Yong-Rae Kwon) 한국정보과학회 2003 한국정보과학회 학술발표논문집 Vol.30 No.2Ⅱ
리팩토링은 외부로 나타나는 행위의 변화없이 내부구조를 바꾸어 소프트웨어의 품질을 높인다. 이러한 리팩토링을 언제, 어디에 적용하는가에 대한 결정은 유지보수자(maintainer)의 주관적인 직관에 따르기 때문에 이를 체계적으로 결정하는 것은 어렵다. 본 논문에서는 메트릭을 이용하여 객체지향 시스템에서 언제, 어떤 리팩토링을 적용할 것인가를 체계적으로 결정하는 방안에 대해서 논의한다. 리팩토링의 최종 결정권은 유지보수자가 가지고 있으므로 리팩토링에 대한 결정을 보조하는 방안에 초점을 맞추었다. 그리고 본 논문에서 제안하는 방법을 6가지 대표적인 리팩토링에 적용시켜보았다.
철골기둥에 적합한 단부보강 합성보 단면 형상에 대한 고찰
류재용(Ryoo Jae-Yong),채흥석(Chae Heung-Suk),최성모(Choi Sung-Mo) 대한건축학회 2011 대한건축학회 학술발표대회 논문집 - 계획계/구조계 Vol.31 No.2(구조계)
In previous studies, we conducted a connection development of end-reinforced composite beam and SRC column. In experiment results, seismic performance was showed more than intermediate moment frame. Based on this results, we are progressing development of end-reinforced composite beam and steel column to increase using. In this study, we reviewed to find optimal connection shape of end-reinforced composite beam and steel column.