http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
우창기,이장규,박성완,김봉각,윤종희,인승현 한국공작기계학회 2002 한국공작기계학회 춘계학술대회논문집 Vol.2002 No.-
The results of source location in terms of AE signal occurred by the spot exciting as suggested in this research, it has been confirmed that AE technique is quite fruitful in figuring out the location of the occurrence, form, size and direction of the defects. Thus, it is expected that the application of the experimental method suggested in this study would make it possible to identify, in the nondestructive way, the location of the defect in the material.
우창기,김배현,이병주,이진춘 대한이비인후과학회 2012 대한이비인후과학회지 두경부외과학 Vol.55 No.8
Mucoepidermoid carcinoma is the most common malignant salivary gland neoplasm. Its sclerosing morphologic variant, however, is an extremely rare entity. Only 15 cases have been reported in the English literature. We report a case of a sclerosing mucoepidermoid carcinoma in the left parotid gland with a review of literature. A fifty seven-year-old female patient presented with left parotid mass. Fine needle aspiration biopsy reported a parotid gland tumor, predominantly benign cystic condition, and the differential diagnosis included benign lymphoepithelial cyst and Warthin’ tumor. Left superficial parotidectomy was performed. Histologically, a well demarcated mass (2.2×1.5×1.0 cm) was composed of a central sclerosis with a few tumor nests and a peripheral lymphoid hyperplasia. The lumen of the tumor glands is filled with mucin stained with mucicarmine. Finally, it was diagnosed as sclerosing mucoepidermoid carcinoma.
반복인장-압축하중을 받는 이온질화 처리한 SM45C의 부식피로 파괴거동에 관한 연구
우창기,김희송 대한기계학회 1989 대한기계학회논문집 Vol.13 No.3
본 논문에서는 기계용 부품소재로 많이 사용되는 SM45C에 대하여 이온질화 처리시 N$_{2}$:H$_{2}$ 가스조성비 변화에 따른 효과가 반복인장-압축하중을 받는 부식피로파괴의 거동에 미치는 영향을 중점적으로 연구하였다. This paper dealt with the effect of the ratios N2 to H2 gas on the corrosion fatigue failure behavior of ion-nitrided SM45C steel specimens. The specimens were water cooled after ion-nitriding at 500.deg. C for 3hrs in 5 Torr, 0.8N$_{2}$ and 0.5N$_{2}$ atmospheres. As the nitrogen concentration increases, the higher compressive residual stresses developed in the surface layer and the depth of nitrided layer increased, which in turn gave rise to increases in fatigue strength and corrosion fatigue life. In the region less than 1.5 * 10$^{5}$ cycles, fatigue failure initiated at the brittle nitrided case, whereas in the region higher than 1.5 * 10$^{5}$ cycles crack initiated from the non-metallic inclusions in the subsurface. The initiation of corrosion fatigue failure was mainly attributed to pitting of case hardened surface layer.
우창기,이장규,윤종회,안종성 한국공작기계학회 2002 한국공작기계학회 추계학술대회논문집 Vol.2002 No.-
Impact behavior of polycarbonate in various defect state was investigated using an instrumented impact tester. A method of analyzing raw impact data was developed and successfully demonstrated the impact behavior in terms of load-displacement and energy-displacement curves. This technique was shown to be capable of separating defect, no-defect initiated fractures as well as their propagation behaviors.
우창기,조견식 한국공작기계학회 2002 한국생산제조학회지 Vol.11 No.5
This search is about slurry wear of SM45C and SUS304, which using standard sand and KUM river sand. The results are as follows ; 1. Mass loss rates of both standard sand and KUM river sand were linearly increased as increasement of time and velocity. 2. The average diameter of sand from relatively, less were rate and portion of larger particles. 3. Wear resistance was linear with time and velocity of liquid jet regardless of type of sand. Also, it was able to evaluate with the formula, HV^2/E calibrated with n, the velocity index. 4. The wear surface in liquid jet experiment was smooth. The maximum wear depth was observed at the location, 2~4mm apart from the center in the condition of 90˚ of collision angle 6mm of nozzle diameter, and 20mm of collision distance. The sectional shape in radial appeared as 'W' shape.