http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
전단동축형 분사기의 유량계수에 대한 형상학적 변수들의 영향
안종현,이근석,안규복,Ahn, Jonghyeon,Lee, Keunseok,Ahn, Kyubok 한국분무공학회 2020 한국액체미립화학회지 Vol.25 No.3
Six shear coaxial injectors for a 3 tonf-class liquid rocket engine using oxygen and methane as propellants were designed and manufactured by considering geometric design parameters such as a recess length and a taper angle. Cold-flow tests on the injectors were performed using water and air as simulants. By changing the water mass flow rate and air mass flow rate, the injection pressure drop under single-injection and bi-injection was measured. The discharge coefficients through the injector oxidizer-side and fuel-side were calculated and the discharge coefficient ratio between bi-injection and single-injection was obtained. Under single-injection, the recess served to reduce the injection pressure drop on the injector fuel-side. For the injectors without recess, the discharge coefficients under bi-injection were almost the same as those under single-injection. However, for the injectors with recess, the taper angle and bi-injection had a significant effect on the discharge coefficient.
안종현 ( Jonghyeon Ahn ),이근석 ( Keunseok Lee ),안규복 ( Kyubok Ahn ) 한국분무공학회 2021 한국액체미립화학회지 Vol.26 No.1
Six shear coaxial injectors with different recess length and taper angle were manufactured. Cold-flow tests on the injectors were performed at room temperature and pressure using water and air as simulants. By changing the water mass flow rate and air mass flow rate, spray images were taken under single-injection and bi-injection. Breakup length and spray angle were analyzed from instantaneous and averaged spray images using image processing techniques. For all the injectors, the breakup length generally decreased as the momentum flux ratio increased at the same gas mass flow rate. The injectors with 7.5° taper angle usually had the longest breakup length and the smallest spray angle. When the taper angle was 15° or more, it hardly affected breakup length and spray angle. The recess length did not influence breakup length but its effect on spray angle depended on the taper angle.
윤원재(Wonjae Yoon),안종현(Jonghyeon Ahn),안규복(Kyubok Ahn),윤호성(Hosung Yoon) 한국추진공학회 2021 한국추진공학회지 Vol.25 No.3
An experimental study was conducted on the spray characteristics of the pintle injector by opening distance. The discharge coefficient of the pintle injector was investigated and the spray angle was measured by taking the spray image by test conditions. As a result of the measurement of the discharge coefficient, it was confirmed that the change in the discharge coefficient of the outer injector was not significant over the experimental conditions, but the change in the discharge coefficient of the inner injector was decreased as the flow rate increased. Measurement of the spray angle showed that the change in the spray angle was not significant in the conditions under which the spray was fully developed, but the spray was not fully developed at low flow rates. This confirmed the possibility of thrust control using the pintle injector.
윤원재(Wonjae Yoon),안종현(Jonghyeon Ahn),안규복(Kyubok Ahn),윤호성(Hosung Yoon) 한국추진공학회 2020 한국추진공학회 학술대회논문집 Vol.2020 No.11
개도에 따른 핀틀 분사기의 분무특성에 대한 실험적 연구를 수행하였다. 분사조건에 따른 핀틀 분사기의 유량계수를 확인하였으며, 분무 이미지 촬영을 통해 분무각을 측정하였다. 유량계수 측정 결과 바깥쪽 분사기는 실험조건에 걸쳐 유량계수 변화가 크지 않았지만 안쪽 분사기는 유량에 따른 유량계수 변화가 큰 것을 확인하였다. 분무각 측정결과 분무가 완전 발달되는 조건에서는 분무각의 변화가 크지 않았으나 낮은 유량에서 분무가 완전 발달되지 않는 경우가 있었다. 이를 통해 핀틀 분사기의 추력조절 가능성을 확인하였다. An experimental study was conducted on the spray characteristics of the pintle injector by opening distance. The discharge coefficient of the pintle injector was investigated and the spray angle was measured by taking the spray image by test conditions. As a result of the measurement of the discharge coefficient, it was confirmed that the change in the discharge coefficient of the outer injector was not significant over the experimental conditions, but the change in the discharge coefficient of the inner injector was decreased as the flow rate increased. Measurement of the spray angle showed that the change in the spray angle was not significant in the conditions under which the spray was fully developed, but the spray was not fully developed at low flow rates. This confirmed the possibility of thrust control using the pintle injector.