http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
- 中文 을 입력하시려면 zhongwen을 입력하시고 space를누르시면됩니다.
- 北京 을 입력하시려면 beijing을 입력하시고 space를 누르시면 됩니다.
RISS 인기검색어
- 검색키워드
- 저자 : R. Bouras (검색결과 3 건)
- 무료
- 기관 내 무료
- 유료
-
High photocatalytic capacity of porous ceramic-based powder doped with MgO
Bouras Dikra,Fellah Mamoun,Mecif Abla,Barillé Régis,Obrosov Aleksei,Rasheed Mohammed 한국세라믹학회 2023 한국세라믹학회지 Vol.60 No.1
To purify water at low cost for our daily life, the effect of ceramic-based (mullite–cristobalite) and (mullite–zircon) powders doped with different amounts of magnesium oxide (MgO) (10 and 20 wt%) was studied. These compounds are made of a local raw material DD3 with addition of zirconia (ZrO2) to create an open porosity. The powders were prepared by the traditional mixing method with the help of an automated crushing. The effect of MgO doping on structural, morphological and photocatalytic properties of the material was studied by various analytical techniques such as X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, infrared, and UV–visible spectrometry. The results of XRD proved that there was a deformation in the crystal structure of the two types of ceramics after addition, which resulted in a shift of the spectra to the right, while SEM proved the presence of pores with a larger size as the proportion of MgO increases. The chemical composition of the basic components of the ceramic compounds as well as the additive was confirmed with EDS and IR spectra. The final results show that ceramics with added zirconia (DD3Z) and doped with 10% of MgO have a better photocatalytic efficiency than ceramics without zirconia. This important effect could be related to the higher rate of porosity, which provides a more active surface. The 10% MgO content showed a high photoactivity of 77.33% in only 15 min. The maximum hydrolysis rate obtained with Orange II was 92.95% after a period of 45 min with DD3Z/MgO powders.
-
Influence of viscosity modifying admixtures on the rheologicalbehavior of cement and mortar pastes
R. Bouras,A. Kaci,M. Chaouche 한국유변학회 2012 Korea-Australia rheology journal Vol.24 No.1
The influence of Viscosity-modifying admixtures (VMA) dosage rate on the steady state rheological properties, including the yield stress, fluid consistency index and flow behaviour index, of cementitious materials is considered experimentally. The investigation is undertaken both at cement paste and mortar scales. It is found that the rheological behaviour of the material is in general dependent upon shear-rate interval considered. At sufficiently low shear-rates the materials exhibit shear-thinning. This behaviour is attributed to flow-induced defloculation of the solid particles and VMA polymer disentanglement and alignment. At relatively high shear-rates the pastes becomes shear-thickening, due to repulsive interactions among the solid particles. There is a qualitative difference between the influence of VMA dosage at cement and mortar scales: at cement scale we obtain a monotonic increase of the yield stress, while at mortar scale there exists an optimum VMA dosage for which the yield stress is a minimum. The flow behaviour index exhibit a maximum in the case of cement pastes and monotonically decreases in the case of mortars. On the other hand, the fluid consistency index presents a minimum for both cement pastes and mortars.
-
Influence of viscosity modifying admixtures on the rheological behavior of cement and mortar pastes
Bouras, R.,Kaci, A.,Chaouche, M. 한국유변학회 2012 Korea-Australia rheology journal Vol.24 No.1
The influence of Viscosity-modifying admixtures (VMA) dosage rate on the steady state rheological properties, including the yield stress, fluid consistency index and flow behaviour index, of cementitious materials is considered experimentally. The investigation is undertaken both at cement paste and mortar scales. It is found that the rheological behaviour of the material is in general dependent upon shear-rate interval considered. At sufficiently low shear-rates the materials exhibit shear-thinning. This behaviour is attributed to flow-induced defloculation of the solid particles and VMA polymer disentanglement and alignment. At relatively high shear-rates the pastes becomes shear-thickening, due to repulsive interactions among the solid particles. There is a qualitative difference between the influence of VMA dosage at cement and mortar scales: at cement scale we obtain a monotonic increase of the yield stress, while at mortar scale there exists an optimum VMA dosage for which the yield stress is a minimum. The flow behaviour index exhibit a maximum in the case of cement pastes and monotonically decreases in the case of mortars. On the other hand, the fluid consistency index presents a minimum for both cement pastes and mortars.
연관 검색어 추천
이 검색어로 많이 본 자료
활용도 높은 자료
