지반공학분야 설계기준 및 표준시방서의 표준화에 관한 연구 - 2차년도 과업을 중심으로 -

이승호,권오균,김낙영,백승철,조현,강인규,김기석,유충식,이강일,백용,Lee, Seung-Ho,Gwon, O-Gyun,Kim, Nak-Yeong,Baek, Seung-Cheol,Jo, Hyeon,Gang, In-Gyu,Kim, Gi-Seok,Yu, Chung-Sik,Lee, Gang-Il,Baek, Yong 한국지반공학회 2015 지반 : 한국지반공학회지 Vol.31 No.7

국내 평가 가이드 라인 제시를 위한 전동식 부항기의 특성 조사에 관한 연구

이승호,김은정,신경훈,남동우,강중원,이승덕,이혜정,이재동,김갑성,Yi, Seung-Ho,Kim, Eun-Jung,Shin, Kyung-Hoon,Nam, Dong-Woo,Kang, Jung-Won,Lee, Seung-Deok,Lee, Hye-Jung,Lee, Jae-Dong,Kim, Kap-Sung 대한침구의학회 2010 대한침구의학회지 Vol.27 No.1

Objectives : The mechanical properties of Korean electric cupping systems are studied via experimental measurements. The study aimed at establishing the fundamentals of industrialization and systemization of oriental medicine device industry, as well as improving the quality of life for many Koreans. Methods : We reviewed the studies on traditional cupping as well as modern one to fine necessary factors for electric cupping systems. To characterize the mechanical properties of Korean electric cupping systems, we measured the pressure characteristics of commercially available electric cupping system by using an automatic pressure acquisition system and a standard cup. The pumping capability was checked at 40 seconds, and the stability of the suction cup was checked at 600 seconds. We also acquired the noise level of each system in clinical setting. To check the portability of each system, we also measured its physical dimensions. We scrutinized system manuals provided by the system manufacturers. Results : It took less than 5 second to reach the pressure if the connection between the air hose and the vacuum valve of the cupping system was secure. Pressure diminished to no more than 10% for 600s for all systems. Noise levels were 55~70 dB. Increase in pressure was too fast to control for a designated vacuum level except for one product. Conclusions : The Pumping ability of the systems is impressive and reliable. Pressure retention ability of each cup is quite reliable and reproducible. Therefore, their mechanical performances were worthy of recommendation. Some of them had noise level higher than 60 dB and they were bothersome. It was also suggested that the control for low to middle pressure needed to be accomplished by the cupping system.

위성망을 이용한 파워 그리드 위기관리 시스템의 테스트베드 구현

이승호,Lee, Seung-Ho 한국전기전자학회 2011 전기전자학회논문지 Vol.15 No.1

본 논문에서는 위성망을 이용한 파워 그리드의 위기관리 시스템을 검증하기 위한 테스트베드 시스템을 제안하였다. 위기관리 시스템의 검증을 위해, 제안된 테스트베드는 위성통신의 통신품질을 기상상황에 맞추어 시뮬레이션 하였으며, 파워 그리드의 동작과 이상상황에 대한 정확한 재현을 위해 FPGA 기반의 Phase Measurement Unit(PMU) 에뮬레이터를 구현하였다. 제안된 위성통신 시뮬레이터는 전국 각 지역의 순간 강수량 및 최대 강수량 데이터를 데이터베이스화하여, 습도와 강수량에 기반을 둔 위성통신의 신뢰성을 모델링 하였으며, 인터넷을 통한 실시간 순간 강수량 데이터를 이용해 실시간 위성통신 신뢰도 맵을 구현하였다. 또한 PMU 에뮬레이터는 FPGA 를 이용한 하드웨어 기반의 에뮬레이터 구현을 통해 동작의 신뢰도를 높였다. 본 논문에서 제안한 테스트베드 시스템은 위성망을 이용한 파워 그리드 위기관리 시스템의 검증과 운영에 적용하였다. In this paper, we propose a testbed system for the crisis management system of the power grid(CMS-PG) using satellite communication network. For the verification of CMS-PG, the proposed system composed of the simulator of satellite communication network and the simulator of phase measurement unit. Proposed satellite communication simulator can evaluate the delay and the robustness of the communication according to the rainfall and the humidity of local site. And the proposed simulator can calculates the voltage stability by hardware implementation using FPGA. Using the proposed testbed system, we adapted its function of crisis management system for the conventional power grid.

Separation and Characterization of Dust and Ground Water Particulates Using Gravitational SPLITT Fractionation.

이승호,박희영,이상근,용성권,음철훈,Lee, Seung Ho,Park, Hui Yeong,Lee, Sang Geun,Yong, Seong Gwon,Eum, Cheol Hun Korean Chemical Society 2001 Bulletin of the Korean Chemical Society Vol.22 No.6

Split-flow thin (SPLITT) cell Fractionation(SF) is a technique that allows separation of particulates and macromolecules into two fractions. A gravitational SF(GSF) system is constructed and tested for its applicability for separation of dust and ground water particulates. When tested with polystyrene latex particles, experimental data were in good agreements with theory. The 9.8 and 21.4㎛ polystyrene particles were successuflly separated in a continuous mode, where the mixture is continuously fed into the GSF channel allowing separation in a large sacle. The GSF system is successfully applied to continuous separation of dust and ground water particels based on the sedimentation coefficient, which is closely related to the particle size. The separations were confirmed by microscopy and energy-dispersive X-ray (EDX) analysos.

PC 인터페이스를 이용한 LCD 구동회로의 PLD 설계

이승호,이주현,Lee, Seung-Ho,Lee, Joo-Hyun 한국조명전기설비학회 2002 조명·전기설비학회논문지 Vol.16 No.1

본 논문에서는 PC 인터페이스를 이용하여 Gray Mode Graphic STN LCD를 구동하는 구동회로를 제안한다. 제안된 구동회로는 사용자가 PC상에서 작업한 이미지 데이터를 PC 인터페이스를 이용하여 LCD로 전송할 수가 있다. 따라서 기존의 방식과는 달리 마이크로프로세서를 사용하지 않기 때문에 사용자가 손쉽게 LCD를 구동할 수 있는 장점이 있다. 제안한 LCD 구동회로 부분은 schematic capture, AHDL, VHDL 등으로 설계하여 시뮬레이션을 수행하고 ALTERA 사의 EPM7192SQC160-15 PLD를 사용하여 구현하였다. PC 인터페이스 부분은 MS-Visual C++ 6.0으로 프로그래밍 하였다. 한편, 제안한 구동회로를 테스트 보드를 구성한 후에 하드웨어 동작 검증을 수행하여 그 효용성을 입증하였다. 본 논문에서 제안한 구동회로를 현재 시판중인 마이크로프로세서를 사용하는 타 업체의 구동회로와 비교한 결과는 구동회로의 작동 편이성, 제작시 소요되는 비용 등에서 우수함을 나타내었다. This paper presents a PLD design of Gray Mode Graphic STN LCD drive circuit using PC interface. The proposed LCD drive circuit doesn\`t use microprocessor for the convenience of users. Thus, the LCD drive circuit can transfer efficiently image data created under PC to LCD. The LCD drive circuit which is modelled in schematic capture, AHDL and VHDL is simulated in functionally through the use of ALTERA MAX+PLUS II. Also, timing simulation is performed by ALTERA EPM7192SQC160-15 PLD implementation. The PC interface part have been programmed in MS-Visual C++ 6.0. The validity and efficiency of the proposed LCD drive circuit have been verified by test board. After comparing this LCD drive circuit to specify it was verified that the developed LCD drive circuit showed good performances, such as convenience of users, low cost.

배터리의 노화 상태를 고려한 배터리 SOC 추정

이승호,박민기,Lee, Seung-Ho,Park, Min-Kee 한국전기전자학회 2014 전기전자학회논문지 Vol.18 No.3

Proper operation of the battery powered systems depends on the accuracy of the battery SOC(State of Charge) estimation, therefore it is critical for those systems that SOC is accurately determined. The SOC of the battery is related to the battery aging and the SOC estimation methods without considering the aging of the battery are not accurate. In this paper, a new method that accurately estimate the SOC of the battery is proposed considering the aging of the battery. A mathematical model for the Battery SOC-OCV(Open Circuit Voltage) relationship is presented using Boltzmann equation and aging indicator is defined, and then the SOC is estimated combining the mathematical model and aging indicator. The proposed method takes the aging of the battery into consideration, which leads to an accurate estimation of the SOC. The simulations and experiments show the effectiveness of the proposed method for improving the accuracy of the SOC estimation. 배터리를 사용하고 있는 시스템에서 배터리의 잔존 용량에 대한 정보는 매우 중요하며, 따라서 정확한 SOC(State of Charge)의 추정이 필요하다. 배터리는 노화됨에 따라 전체 사용 가능 용량이 줄어들고 성능이 떨어지는데 이러한 노화의 영향을 고려하지 않는 배터리의 SOC 추정 방법은 추정의 정확도가 떨어지는 단점이 있다. 따라서 본 논문에서는 배터리의 노화 상태를 고려하여 배터리의 SOC를 추정하는 새로운 방법을 제안한다. 제안한 방법에서는 배터리의 전압-SOC 특성 곡선을 Boltzmann 방정식을 사용하여 모델링하고 노화 지표를 정의하며, 노화 지표를 Boltzmann 방정식 모델과 결합하여 SOC를 추정한다. 따라서 제안한 방법은 배터리의 노화 상태를 SOC 추정에 반영하여 노화된 배터리에 대한 정확한 SOC 추정이 가능하다. 또한 새 배터리와 1년 사용한 배터리에 대한 실험과 시뮬레이션을 통하여 제안한 방법의 유효성을 확인한다.

크리프 균열개시 시간에 대한 구속효과 영향의 정량화

이승호,정현우,김윤재,Lee, Seung-Ho,Jung, Hyun-Woo,Kim, Yun Jae 한국압력기기공학회 2020 한국압력기기공학회 논문집 Vol.16 No.2

A new elastic-plastic-creep constraint parameter is proposed to quantify the effect of constraint on creep crack initiation times. It represents the difference between the transient elastic-plastic-creep crack-tip opening stress and the Riedel-Rice opening stress field in plane strain, which can be determined analytically. Application of the proposed parameter to a large set of creep crack growth test data using C(T) and SEN(B) specimens of Type 316H stainless steel at 550℃ shows that creep crack initiation times can be more accurately characterized by the C⁎-integral together with the proposed parameter.

물산업 해외진출방안

이승호,Lee, Seung-Ho 한국수자원학회 2016 물과 미래(한국수자원학회지) Vol.49 No.5

일본의 교통안전시설 정비 사례 - 교통안전대책을 중심으로 -

이승호,Lee, Seung-Ho 한국도로학회 2005 도로 : 도로학회지 Vol.7 No.1

큰 두위를 주소로 내원하여 헌터 증후군으로 일찍 진단된 증례 1례

이승호,박우성,이영석,유지숙,Lee, Seung Ho,Park, Woo Sung,Lee, Young Seok,Yu, Jeesuk 대한유전성대사질환학회 2014 대한유전성대사질환학회지 Vol.14 No.2

A 25-month-old boy was referred to the hospital due to large head detected on routine physical examination. At visit, dysmorphic facial appearances, including broad nose, prominent forehead, and coarse face, were noted. Nasal obstruction with nasal voice, prominent adenoids, and bilateral middle ear effusions were detected. His abdomen was distended, and liver and spleen were palpated about 3 finger and 2 finger breadths, respectively. He was operated for bilateral inguinal hernias. The motion of both elbow joints was mildly limited on supination and pronation. Urinary level of glycosaminoglycan was elevated and the enzyme activity of iduronate sulfatase in leukocytes was decreased. The mutational analysis of the gene iduronate 2-sulfatase (IDS) revealed c.263G>A (p.Arg88His) mutation. His developmental scale showed delayed development and there was cardiac valvular involvement (tricuspid regurgitation and mitral valve prolapse). After the diagnosis of Hunter syndrome, enzyme replacement therapy started on a weekly basis without progression of any clinical features. Here we report a case of early diagnosed Hunter syndrome detected by large head on routine examination. Thus, it is important to associate Hunter syndrome in the patient with large head especially, if there is the history of bilateral inguinal hernia and prominent adenoids to increase the possibility of early diagnosis and treatment.