http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
김정규 ( Jung-gyu Kim ),양형식 ( Hyung-sik Yang ),김종관 ( Jong-gwan Kim ) 대한화약발파공학회 2016 화약발파 Vol.34 No.3
성형폭약의 조절발파 효과를 확인하기 위하여 정밀폭약에 금속라이너의 재질과 두께를 달리하여 상대적으로 폭속이 작은 암석 절단용 성형폭약을 제작하였다. 성형폭약이 암반 내부에서 기폭될 때 방향성 절단을 유도하기 위하여 폭약 양쪽으로 금속라이너를 부착하였다. 또한 콘크리트 부재 실험을 통하여 성형폭약의 성능을 확인하였고 성형폭약과 공벽과의 적정 이격거리를 유지하기 위한 센터 가이더를 제작하였다. 실험결과 0.8 mm 두께의 Fe 라이너가 장착된 성형폭약을 사용할 때 가장 깊은 노치가 형성되었고, 콘크리트 부재의 방향성 절단을 확인할 수 있었다. The shaped charge were made for identifying the effect of controled blasting using relatively low VOD explosive for cutting rock mass with changing quality and thickness of metal liner. The metal liner was attached on both sides of a charge for directional cutting, when the shaped charge exploded in rock mass. Also, a efficiency of shaped charge was identified by concrete member experiment. And a center guide used for maintaining stand-off between shaped charge and hole wall. A case of Fe liner of thickness 0.8mm formed the deepest notch of experiments and the directional cutting of concrete member was identified.
다층 주방식 채광 광산에서 낙반이 채광장 천반과 광주에 미치는 영향
김종관 ( Jong Gwan Kim ),양형식 ( Hyung Sik Yang ) 대한화약발파공학회 2016 화약발파 Vol.34 No.4
다층 주방식 광체의 개발에서 상부 채광장 천반의 붕락이 하부 편 광주에 미치는 영향을 보기 위하여 AUTODYN으로 수치해석 하였다. 그 결과 하부 채광장 천반에서의 최대 변위와 응력은 각각 0.001mm LC 36MPa 정도였고, 광주에서의 최대 변위와 응력은 각각 0.0003 mm 및 3 MPa 정도였다. 상부 채광장의 천반암석의 절반이 붕락하는 상황을 가정했을 때 하부 채광장 천반과 광주의 손상도는 0.03 정도로 나타났다. Influence of rock fall from upper-level roofs to lower-level roofs and pillars at a multi layered room and pillar mine was numerically simulated by using AUTODYN. The analysis results showed that the maximum displacement and stress in the roof of the lower-level stope are respectively 0.001 mm and 36 MPa, and those in the pillars of the lower-level stope are 0.0003 mm and 3 MPa. The maximum damage levels in the roof and pillar of the lower-level stope were evaluated to be about 0.03 when a half of the roof rock of the upper-level stope was assumed to be fallen to the floor.
김정규(Jung-Gyu Kim),정승원(Seung-Won Jung),김준하(Jun-Ha Kim),김종관(Jong-Gwan Kim) 한국암반공학회 2021 터널과지하공간 Vol.31 No.6
갱내채광개발의 안정성 문제로 굴착단면을 축소하였을 때 발생한 경제적 손실을 최소화하기 위해 발파효율을 증가시킬 필요가 있으며, 이를 위해 새로운 발파 설계를 제안하였다. 본 연구에서는 현장의 생산발파, 생산발파에 확대공을 2열 추가한 1차 제안발파 그리고 확대공에 1열만 추가하여 비대칭을 이루는 2차 제안발파의 발파효율을 비교하였다. 발파효율 평가지표로는 굴진율과 파쇄입도로 선정하였다. 굴진율의 경우 일반대비 1차 제안발파는 6.07%, 2차 제안발파는 4.65% 향상하였고, 파쇄입도의 경우 P80 기준으로 일반발파 대비 1차 제안발파는 약 58%, 2차 제안발파는 약 47% 파쇄입도가 감소하였다. 평가지표에 따라 1차 제안발파가 2차 제안발파보다 좋은 발파효율을 보이지만, 평가지표의 결과의 차이가 미비하여 1차 제안발파에 추가적으로 소요된 작업시간과 비용을 고려하였을 때 2차 제안발파인 비대칭 V-cut이 현장에 더 적합한 발파설계라 판단된다. It is necessary to increase the blasting efficiency in order to minimize the economic loss caused when the excavation cross section is reduced due to the stability problem of underground mining development, and for this, a new blasting design is proposed. In this study, the blasting efficiency of the general design in the field, the suggestion designⅠ, which added two columns to production blasting, and the suggestion design II, which added one column to create asymmetry, is compared. Advance rate and fragmentation were selected as the evaluation index of the blasting efficiency. In the case of advance rate, compared to the normal, the suggestionⅠ improved by 6.07% and the suggestionⅡ improved by 4.65%. In the case of fragmentation, based on P80, compared to the normal, the suggestionⅠ reduced about 58% and the suggestionⅡ was about 47%. Accoording to the evaluation index, the suggestion designⅠ shows better blasting efficiency than the suggestion designⅡ. But considering the additional work time and cost required for the suggestion designⅠ due to the insignificant difference in the evaluation index results, the asymmetry V-cut, the suggestion designⅡ, is judged to be a more suitable blasting design for the site.
김종관(Jong-Gwan Kim) 한국암반공학회 2020 터널과지하공간 Vol.30 No.1
노천채광에서 경제적인 채광을 위한 채광장 형성은 매우 중요하며, 대규모 채광을 위한 발파작업은 사면의 안정성에 영향을 미칠 수 있으므로 이에 대한 고려가 필요하다. 본 연구에서는 사면설계와 발파 조건을 달리하면서 사면 안정성에 미치는 영향 인자의 기여율을 검토하였다. 설계인자는 암반의 물성, 사면각도, 벤치높이이며, 발파 조건은 장약량과 거리를 달리하여 반영하였다. 사면의 안전율은 3차원 모델링을 통해 전단강도감소기법으로 산출하였으며, 기여율은 암반사면의 물성이 94.8%로 다른 설계인자들에 비해 상대적으로 높았으며, 사면각도 0.89%, 벤치높이 0.58%, 발파는 3.73% 정도의 영향을 미치는 것으로 나타나, 사면과 근접거리에서의 발파는 사면의 안정성에 영향을 줄 수 있음을 알 수 있다. In surface mining, it is very important to create a mining area for economical mining. This study examined the contribution of design factors on slope stability with different slope design and blasting conditions. The design factors were the properties of the rock, the slope angle and the bench height, and the blasting conditions were reflected at different explosive weight and distances. The safety factor of slope was calculated by shear strength reduction method through 3D modeling, and the contribution rate of rock slope was 94.8%, which is relatively higher than other design factors, slope angle 0.89%, bench height 0.58%, and blasting It is shown that it affects about 3.73%, and it can be seen that blasting at a close distance can affect the stability of the slope.
적응 퍼지제어기에 의한 IPMSM 드라이브의 센서리스 벡터제어
金鍾官(Jong-Gwan Kim),朴炳相(Byung-Sang Park),鄭東和(Dong-Hwa Chung) 대한전기학회 2006 전기학회논문지 B Vol.55 No.2
This paper proposes to position and speed control of interior permanent magnet synchronous motor(IPMSM) drive without mechanical sensor. Also, this paper develops a adaptive fuzzy controller based fuzzy logic control for high performance of PMSM drives. In the proposed system, fuzzy control is used to implement the direct controller as well as the adaptation mechanism. A Gopinath observer is used for the mechanical state estimation of the motor. The observer was developed based on nonlinear model of IPMSM, that employs a d-q rotating reference frame attached to the rotor. A Gopinath observer is implemented to compute the speed and position feedback signal. The validity of the proposed scheme is confirmed by various response characteristics.