http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
지지체 투과저항과 코팅층의 두께가 PDMS 복합막의 에틸렌/질소의 투과성능에 미치는 영향
김정훈,최승학,박인준,이수복,강득주 한국막학회 2004 멤브레인 Vol.14 No.1
PDMS (polydimethylsiloxane) 복합막을 통한 기체분리 공정에서 다공성 지지체의 투과저항과 PDMS 코팅두께가 에틸렌/질소의 분리성능(투과도, 선택도)에 미치는 영향에 관하여 조사하였다. 이를 위해 Pinnau 등이 제시한 복합막 투과저항 모델이론식〔1〕이 사용되었다. 지지체의 투과도 또는 투과저항은 PES (polyethersulfone)/NMP(N-methyl-2-pyrrolidone) 고분자 용액의 농도를 변화시키면서 조절하였다. 복합막은 PES 지지체 위에 n-hexane에 녹인 2액형 PDMS 용액을 spin coater를 사용해 코팅하여 제조하였다. 선택층의 코팅 두께는 spin coater의 회전속도를 통해 조절하였다. 투과기체 분리특성은 단일기체 투과도 측정 장치를 통해 조사하였으며, 지지체 및 복합막의 단면구조 및 코팅두께는 SEM (scanning electron microscope)을 통하여 확인하였다 얻어진 실험결과는 복합막의 투과저항모델의 이론식과 매우 잘 일치함을 확인 할 수 있었다. 에틸렌/질소의 분리에 있어 PDMS 막 고유의 선택도를 얻기 위해서는 지지체의 투과저항과 코팅층의 최적화가 중요함을 확인하였다. The effect of porous support layer resistance and PDMS (polydimethylsiloxane) coating thickness on ethylene/nitrogen separation of composite membranes was studied with the model of Pinnau and Wijmans〔1〕. To control the support resistance (or permeance), PES porous membranes were prepared by phase inversion process with various PES/NMP dope concentrations. The thickness of selective PDMS top layer was controlled by using a spin coater. Its cross-section and coating thickness were observed by scanning electron microscope (SEM). Pure gas permeation test was done with ethylene and nitrogen, respectively. The experimental result for olefin/nitrogen separation process matched well with theoretical result from the model used. The result shows that optimization between PDMS coating thickness and support resistance is important to get PDMS composite membranes with best performance.
권승림,박윤범,정동수,김종보,강득주,Kwon, S.L.,Park, Y.B.,Jung, D.S.,Kim, C.B.,Kang, D.J. 대한설비공학회 1995 설비공학 논문집 Vol.7 No.4
R502 has been extensively used as a working fluid in transport refrigerating vehicles and low temperature refrigerating machines but is to be phased out by the end of 1995 due to ozone layer depletion problem. In this study, both theoretical cycle analysis and experiments were carried out to examine the best substitutes for R502. Theoretical results indicate that the alternatives available in the market today may replace R502 without significant changes in the system without suction line heat exchanger(SLHX). When the system contains a SLHX, however, COPs of the alternatives increase up to approximately 15~20% than those without the SLHX. But simultaneously, the discharge temperatures of the compressor also increrease significantly with the SLHX. Actual test results obtained from the experiment with a transport vehicle's refrigerator indicate the similar trend as those of the theoretical results. Especially, HFCs and their mixtures show lower discharge temperature than those of R502, which is one of the desirable features. Further research is needed to study the effect of the SLHX on the performance of the real machine as well as on the oil return for reliability of the system.
박동민,정동수,김종보,강득주,Park, D.M.,Jeoung, D.S.,Kim, J.B.,Kang, D.J. 대한설비공학회 1997 설비공학 논문집 Vol.9 No.2
This paper is concerned about the performance of alternative refrigerants of R-502 which has been widely used in transport and low temperature refrigeration. A breadboard heat pump was constructed with counterflow heat exchangers and tested with R-502 and transitional alternatives of R-402A and R-402B and long-term alternatives of R-404A and R-507 to compare the performance of each refrigerant. Measurements were conducted at two different condensing temperatures of $43.3^{\circ}C$ and $52.0^{\circ}C$ and the evaporating temperature was varied over a range from $-25^{\circ}C$ to $-5^{\circ}C$. The evaporator superheat and condenser subcooling were maintained constant at about $5^{\circ}C$ for all tests. Test results showed that all alternative fluids tested in this research work can be used as 'drop-in' fluids to replace R-502 without any major problem. It is also found that in the long run HFC alternatives are to be used due to their favorable environmental characteristics and better performance.
실록산계 고분자 막을 통한 올레핀/질소 기체 투과 거동
이수복,신효진,최승학,김정훈,박인준,노재성,강득주 한국막학회 2003 멤브레인 Vol.13 No.4
폴리올레핀 산업에서 발생되는 올레핀 함유 배 가스(off-gas)에서 올레핀만을 선택적으로 분리하기 위해, 폴리디메틸실록산(Polydimethylsiloxane)계열의 막 소재들에 대한 올레핀과 질소의 투과특성을 연구하였다. 막 소재로는 가교 형태의 폴리디메틸실록산(Polydimethylsiloxane, 이하 PDMS라 칭함)막, 폴리실록산이미드(Polysiloxaneimide, 이하 PSI라 칭함)막, 아크릴변성 Oligo-PDMS가 부가된 Oligo-PDMS막들을 대상으로 공급기체의 온도(-20~50℃)와 압력(1∼25 atm)을 변화시키면서 에틸렌(C2H4), 프로필렌(C3H6), 부틸렌(C4H8), 질소(N2) 기체의 단일투과특성을 조사하였다. 실험결과, 사용되는 막소재의 특징에 따라 다양한 투과특성을 보였다. 세 가지 막소재중에서 PDMS막이 가장 넓은 사용압력범위에서 높은 에틸렌투과도 및 에틸렌/질소의 분리특성을 보였으며 이 막을 대상으로 여러 투과조건에서 투과특성을 연구하였다. 선택된 가교 PDMS막을 통한 올레핀, 질소 기체들의 투과도는 투과기체의 분자크기(확산도 선택성)보다, 투과기체의 응축온도(용해도 선택성)에 좌우되는 경향을 보였다. 공급기체의 온도가 감소하거나 압력이 증가할 때, 응축성 기체인 올레핀 기체의 투과도는 증가하고, 비응축성 기체인 질소는 감소하는 특징을 보였으며 이에 따라 올레핀/질소의 선택도가 크게 증가하는 특징을 보였다. 이러한 결과들은 고무상 고분자막에서 보여지는 응축성, 비응축성 기체들의 전형적인 투과특성을 보여준다. For the olefin recovery from polyolefin off-gas, the permeation behaviors of olefins and nitrogen were investigated through three kinds of PDMS membranes - cross-linked PDMS membranes, a polysiloxaneimide membrane, and oligo-PDMS modified PDMS membranes. Their pure gas permeabilities were measured as a function of operation temperature(-20 to 50℃) and pressure(1 to 25 atm) with ethylene(C2;H4), propylene(C3;H6), butylene(C4;H8), and nitrogen(N2) gases. The permeabilities of olefins and nitrogen highly depended upon the nature of PDMS membranes. Among these membranes, cross-linked PDMS membranes showed stable and high olefin/nitrogen selectivities over a wide operation pressure range and further study in various test conditions. Their permeability of olefin and nitrogen were governed by the condensation temperature(solubility selectivity) and plasticization, not the order of the size(diffusivity selectivity) of gases, which matched well with the general permeation behavior of rubbery polymeric membranes for condensable and non-condensable gases. With increasing feed pressure or decreasing feed temperature, the permeabilities of more condensible olefins increase highly, presumably due to high solubility and plasticization, but that of non-condensible nitrogen decreases slightly and thus, the selectivities of olefin/nitrogen increase highly.